| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| CISPR 18-3 AMD 1-1996 | 架空電力線路和高壓設備的無線電干擾特征.第3部分:將無線電噪聲產生降到最少的操作規程;修改件1 | Radio interference characteristics of overhead power lines and high-voltage equipment - Part 3: Code of practice for minimizing the generation of radio noise; Amendment 1 |
| CISPR 18-3-1986 | 高架電線和高壓設備的無線干擾特性.第3部分:無線噪聲產生的最小化的規范 | Radio interference characteristics ofoverhead power lines and high-voltage equipmentPart 3:Code of practice for minimizing the generationof radio noise |
| IEC 59/502/PAS-2008 | IEC/PAS 60704-2-XX,ED.1.0:家用和類似用途電器.氣載噪聲測定用試驗規程.第2-XX部分:家用食品廢棄物處理器 | IEC/PAS 60704-2-XX, ED. 1.0: Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-XX: Particular requirements for household food waste disposers |
| IEC 60034-9 AMD 1-2007 | 旋轉電機.第9部分:噪聲限值.修改件1 | Rotating electrical machines - Part 9: Noise limits; Amendment 1 |
| IEC 60034-9 Edition 4.1-2007 | 旋轉電機.第9部分:噪聲限值 | Rotating electrical machines - Part 9: Noise limits |
| IEC 60034-9-2003 | 旋轉電機.第9部分:噪聲限值 | Rotating electrical machines - Part 9: Noise limits |
| IEC 60034-9-2007 | 旋轉電機噪聲測定方法及限值 第３部分：噪聲限值 | Measurement of airborne noise emitted by rotating electrical machines and the noise limits -Part 3:Noise limits |
| IEC 60151-18-1968 | 電子管電性能的測量 第18部分:由機械或聲音激勵引起的噪聲的測量方法 | Measurements of the electrical properties of electronic tubes. Part 18 : Methods of measurement of noises due to mechanical or acoustic excitations |
| IEC 60151-4-1963 | 電子管電性能的測量 第4部分:噪聲系數的測量方法 | Measurements of the electrical properties of electronic tubes. Part 4 : Methods of measuring noise factor |
| IEC 60151-7-1964 | 電子管電性能的測量 第7部分:等效噪聲電阻的測量 | Measurements of the electrical properties of electronic tubes. Part 7 : Measurement of equivalent noise resistance |
| IEC 60195-1965 | 固定電阻器產生電流噪聲測量方法 | Method of measurement of current noise generated in fixed resistors |
| IEC 60235-2A-1974 | 微波管電性能的測量 第2部分:一般測量 補充1:第4章:寄生噪聲的測量方法 | Measurement of the electrical properties of microwave tubes. Part 2 : General measurements. First supplement: Chapter V: Methods of measuring parasitic noise |
| IEC 60244-3B-1972 | 無線電發射機的測量方法 第3部分:有用調制和無用調制 補充2:無用調制，包括交流及噪聲調制 | Methods of measurement for radio transmitters. Part 3 : Wanted and unwanted modulation. Second supplement: Unwanted modulation, including hum and noise modulation |
| IEC 60510-1-5-1988 | 衛星地面站用無線電設備的測量方法 第1部分:分系統和分系統組合通用的測量 第5節:噪聲溫度測量 | Methods of measurement for radio equipment used in satellite earth stations. Part 1: Measurements common to sub-systems and combinations of sub-systems. Section Five: Noise temperature measurements |
| IEC 60510-2-3-1989 | 衛星地面站用無線電設備的測量方法 第2部分:分系統測量 第3節:低噪聲放大器 | Methods of measurement for radio equipment used in satellite earth stations; part 2: measurements for sub-systems; section three: low-noise amplifier |
| IEC 60534-8-1-2005 | 工業過程控制閥.第8-1部分:噪聲的考慮.氣動流流經控制閥產生的噪聲的實驗室測量 | Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves |
| IEC 60534-8-2-1991 | 工業過程控制閥 第8部分:噪聲的考慮 第2節:流動液流經控制閥產生的噪聲的實驗室測量 | Industrial-process control valves; part 8: noise considerations; section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves |
| IEC 60534-8-3-2010 | 工業過程控制閥.第8-3部分:噪聲的考慮.控制閥的氣動噪聲預測法 | Industrial-process control valves.Part 8-3: Noise considerations.Control valve aerodynamic noise predictionmethod |
| IEC 60534-8-4 Corridendum 1-2006 | 工業過程控制閥.第8-4部分:噪聲問題.預測液體動力流產生的噪聲.勘誤1 | Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow; Corrigendum 1 |
| IEC 60534-8-4 Corrigendum 1-2006 | 工業過程控制閥.第8-4部分:噪聲問題.預測液體動力流產生的噪聲.技術勘誤1 | Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow; Corrigendum 1 |
| IEC 60534-8-4-2005 | 工業過程控制閥.第8-4部分:噪聲問題.預測液體動力流產生的噪聲 | Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow |
| IEC 60704-2-1-2000 | 家用和類似用途電氣設備.測定空氣噪聲的試驗規程.第2-1部分:真空吸塵器的特殊要求 | Household and similar electrical applicances - Test code for the determination of airborne acoustical noise - Part 2-1: Particular requirements for vacuum cleaners |
| IEC 60704-2-10-2004 | 家用和類似用途電器.測定空中傳播噪聲的試驗規范.第2-10部分:電爐灶、爐架和微波爐及其任意組合的特殊要求 | Household and similar electrical apliances - Test code for the determination of airborne acoustical noise - Part 2-10: Particular requirements for electric cooking ranges, ovens grills microwave ovens and any combination of these |
| IEC 60704-2-11-1998 | 家用和類似用途電器 測定空中傳播噪聲的試驗規范 第2-11部分:電動食品加工機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-11: Particular requirements for electrically-operated food preparation appliances |
| IEC 60704-2-13-2011 | 家用和類似用途電器.測定空中傳播噪聲的試驗規范.第2-13部分:抽油煙機的詳細要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-13: Particular requirements for range hoods |
| IEC 60704-2-14-2007 | 家用和類似用途電器.氣載噪聲的測定用試驗規則.第2-14部分:制冷機、冷凍食品儲藏柜和食品凍柜的專用要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-14: Particular requirements for refrigerators, frozen-food storage cabinets and food frozeers |
| IEC 60704-2-3 AMD 1-2005 | 修改件1.家用和類似用途電器.測定空中傳播的噪聲的試驗規程.第2-3部分:洗碗機的特殊要求 | Amendment 1 - Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-3: Particular requirements for dishwashers |
| IEC 60704-2-3 Edition 2.1-2005 | 家用和類似用途電器.測定空中傳播噪聲的試驗規程.第2-3部分:洗碗機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-3: Particular requirements for dishwashers |
| IEC 60704-2-3-2004 | 家用和類似用途電器.測定空中傳播的噪聲的試驗規程.第2-3部分:洗碟機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-3: Particular requirements for dishwashers |
| IEC 60704-2-4-2001 | 家用和類似用途電器 測定空中傳播噪聲的試驗規范 第2-4部分：洗衣機和離心式脫水機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-4: Particular requirements for washing machines and spin extractors |
| IEC 60704-2-5-2005 | 家用和類似用途電器.測定空中傳播噪聲的試驗規程.第2-5部分:貯熱式房間電暖器的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-5: Particular requirements for electric thermal storage room heaters |
| IEC 60704-2-6-2005 | 家用和類似用途電器.空氣傳播噪聲測定的試驗規范.第2-6部分:滾筒干衣機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-6: Particular requirements for tumble dryers |
| IEC 60704-2-7-1997 | 家用和類似用途電器 測定空中傳播噪聲的試驗規范 第2-7部分:電風扇的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2: Particular requirements for fans |
| IEC 60704-2-8-1997 | 家用和類似用途電器 測定空中傳播噪聲的試驗規范 第2-8部分:電動剃須刀的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2: Particular requirements for electric shavers |
| IEC 60704-2-9-2003 | 家用及類似用途電器.測定空中傳播噪聲的試驗規范.第2-9部分:電動毛發護理用具的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-9: Particular requirements for electric hair care appliances |
| IEC 60704-3-2006 | 家用和類似用途電器.測定空中傳播噪聲的試驗規范.第3部分:測定和檢驗宣稱噪聲發出值的規程 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 3: Procedure for determining and verifying declared noise emission values |
| IEC 60749-16-2003 | 半導體器件.機械和氣候試驗方法.第16部分:粒子沖擊噪聲探測(PIND) | Semiconductor devices - Mechanical and climatic test methods - Part 16: Particle impact noise detection (PIND) |
| IEC 60835-3-4-1993 | 數字微波無線電傳輸系統使用設備的測量方法 第3部分:衛星地面站的測量 第4節:低噪聲放大器 | Methods of measurement for equipment used in digital microwave radio transmission systems; part 3: measurements on satellite earth stations; section 4: low noise amplifier |
| IEC 60883-1987 | 磁帶錄像機的色度信號與隨機噪聲之比的測量方法 | Measuring method for chrominance signal-to-random noise ratio for video tape recorders |
| IEC 61063-1991 | 聲學 汽輪機及被驅動機械發出的空氣傳播噪聲的測量 | Acoustics; measurement of airborne noise emitted by steam turbines and driven machinery |
| IEC 61196-1-107-2005 | 同軸通信電纜.第1-107部分:電氣試驗方法.電纜顫噪轉換電平試驗(機械感應噪聲) | Coaxial communication cables - Part 1-107: Electrical test methods - Test for cable microphony charge level (mechanically induced noise) |
| IEC 61265 Corrigendum 1-1995 | 電聲學.航空噪聲測量儀器.在運輸機噪聲鑒定中測量三分之一倍頻帶聲壓級裝置的性能要求 | Electroacoustics - Instruments for measurement of aircraft noise - Performance requirements for systems to measure one-third-octave band sound pressure levels in noise certification of transport-category aeroplanes |
| IEC 61265-1995 | 電聲學 航空噪聲測量儀器 在運輸機噪聲鑒定中測量三分之一帶寬倍頻聲壓級裝置的性能要求 | Electroacoustics - Instruments for measurement of aircraft noise - Performance requirements for systems to measure one-third-octave band sound pressure levels in noise certification of transport-category aeroplanes |
| IEC 61290-3-2008 | 光學放大器.試驗方法.第3部分:噪聲指數參量 | Optical amplifiers - Test methods - Part 3: Noise figure parameters |
| IEC 62150-4-2009 | 纖維光學有源元件和器件.試驗和測量規程.第4部分:應用時域光學檢測系統檢測相對強度噪聲 | Fibre optic active components and devices - Test and measurement procedures - Part 4: Relative intensity noise using a time-domain optical detection system |
| IEC 62333-1-2006 | 數字器件和設備用噪聲抑制片.第1部分:定義和一般性能 | Noise suppression sheet for digital devices and equipment - Part 1: Definitions and general properties |
| IEC 62333-2-2006 | 數字器件和設備用噪聲抑制片.第2部分:測量方法 | Noise suppression sheet for digital devices and equipment - Part 2: Measuring methods |
| IEC 62333-3-2010 | 數字器件和設備用噪聲抑制片.第3部分:噪聲抑制片的參數特性 | Noise suppression sheet for digital devices and equipment - Part 3: Characterization of parameters of noise suppression sheet |
| IEC/PAS 60704-2-15-2008 | 家用和類似用途電器.氣載噪聲測定用試驗規程.第2-15部分:家用食品廢棄物處理機的特殊要求 | Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-15: Particular requirements for household food waste disposers |
| ISO 10302-1-2011 | 聲學.小型通風裝置輻射空氣噪聲的測量.第1部分:空氣噪聲測量 | Acoustics.Measurement of airborne noise emitted and structure-borne vibration induced by small air-moving devices.Part 1: Airborne noise measurement |
| ISO 10996-1999 | 攝影 靜止圖像放映機 噪聲測定 | Photography - Still-picture projectors - Determination of noise emissions |
| ISO 11200 Technical Corrigendum 1-1997 | 聲學 機器和設備發射的噪聲 工作位置和其他指定位置發射聲壓級的測量的基本標準的使用導則 技術勘誤1 | Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions; Technical Corrigendum 1 |
| ISO 11200-1995 | 聲學 機器和設備發射的噪聲 工作位置和其他指定位置發射聲壓級的測量的基本標準的使用導則 | Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions |
| ISO 11201-2010 | 聲學.機器和設備發射的噪聲.在一個反射平面上方可忽略環境校正條件下進行工作位置和其他指定位置的發射聲壓 | Acoustics.Noise emitted by machinery and equipment.Determination of emission sound pressure levels at a workstation and at other specified positions in an essentially freefield over a reflecting plane with negligible environmentalcorrections |
| ISO 11202 Technical Corrigendum 1-1997 | 聲學.機器和設備發射的噪聲.工作位置和其他指定位置發射聲壓級的測量.現場簡易法.技術勘誤1 | Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Survey method in situ; Technical Corrigendum 1 |
| ISO 11202-2010 | 聲學.機器和設備發射的噪聲.應用近似環境修正法對工作站和其他指定位置發射聲壓級進行測定 | Acoustics.Noise emitted by machineryand equipment.Determination ofemission sound pressure levels at a workstation and at other specified positionsapplying approximate environmentalcorrections |
| ISO 11203-1995 | 聲學 機器和設備發射的噪聲 從聲功率級測定工作位置和其他指定位置發射聲壓級 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level |
| ISO 11204-2010 | 聲學.機器和設備發射的噪聲.應用精確環境校準在工作位置和其他指定位置的發射聲壓級測量 | Acoustics.Noise emitted by machinery and equipment.Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| ISO 11205-2003 | 聲學.機械和設備發射的噪聲.利用聲強現場測定工作位置和其他指定位置發射聲壓級的工程法 | Acoustics - Noise emitted by machinery and equipment - Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity |
| ISO 11689 Technical Corrigendum 1-2007 | 聲學.機械和設備發射噪聲數據的比較程序.技術勘誤1 | Acoustics - Procedure for the comparison of noise-emission data for machinery and equipment; Technical Corrigendum 1 |
| ISO 11689-1996 | 聲學 機器和設備發射噪聲數據的比較方法 | Acoustics - Procedure for the comparison of noise-emission data for machinery and equipment |
| ISO 11690-1-1996 | 聲學 低噪聲機器工作間設計的推薦實用規程 第1部分:噪聲控制策略 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 1: Noise control strategies |
| ISO 11690-2-1996 | 聲學 低噪聲機器工作間設計的推薦實用規程 第2部分:噪聲控制措施 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 2: Noise control measures |
| ISO 11819-1-1997 | 聲學 路面對交通噪聲影響的測量 第1部分:統計旁路法 | Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 1: Statistical pass-by method |
| ISO 12001-1996 | 聲學 機器和設備發射的噪聲 噪聲試驗規程的介紹和起草規則 | Acoustics - Noise emitted by machinery and equipment - Rules for the drafting and presentation of a noise test code |
| ISO 13332-2000 | 往復式內燃機 在發動機底座處測量由高速和中速往復式內燃機產生的結構噪聲的試驗規程 | Reciprocating internal combustion engines - Test code for the measurement of structure-borne noise emitted from high-speed and medium-speed reciprocating internal combustion engines measured at the engine feet |
| ISO 13472-1-2002 | 聲學.施工現場路面對噪聲吸收性能的測量.第1部分:擴大表面法 | Acoustics - Measurement of sound absorption properties of road surfaces in situ - Part 1: Extended surface method |
| ISO 13472-2-2010 | 聲學.施工現場路面對噪聲吸收性能的測量.第2部分:反射表面用現場法 | Acoustics - Measurement of sound absorption properties of road surfaces in situ - Part 2: Spot method for reflective surfaces |
| ISO 14163-1998 | 聲學 消聲器噪聲控制指南 | Acoustics - Guidelines for noise control by silencers |
| ISO 14509-1-2008 | 小型船.動力娛樂船排放的空氣噪聲.第1部分:經過測量程序 | Small craft - Airborne sound emitted by powered recreational craft - Part 1: Pass-by measurement procedures |
| ISO 14509-2-2006 | 小艇.動力娛樂船排放空氣噪聲測定.第2部分:用基準船作噪聲評估 | Small craft - Airborne sound emitted by powered recreational craft - Part 2: Sound assessment using reference craft |
| ISO 14509-3-2009 | 小型船舶.動力游艇發出的聲音.第3部分:利用計算和測量程序評定噪聲 | Small craft - Airborne sound emitted by powered recreational craft - Part 3: Sound assessment using calculation and measurement procedures |
| ISO 15086-1-2001 | 液壓傳動 部件和系統的流體噪聲特性的測定 第1部分：引言 | Hydraulic fluid power - Determination of fluid-borne noise characteristics of components and systems - Part 1: Introduction |
| ISO 15086-2-2000 | 液壓傳動 元件和系統油液通過孔徑噪聲特性的測定 第2部分:管路油液中聲音速度的測定 | Hydraulic fluid power - Determination of fluid-borne noise characteristics of components and systems - Part 2: Measurement of speed of sound in a fluid in a pipe |
| ISO 15664-2001 | 聲學 開放式工廠的噪聲控制設計規程 | Acoustics - Noise control design procedures for open plant |
| ISO 15667-2000 | 聲學 采用隔聲罩和隔聲小室的噪聲控制指南 | Acoustics - Guidelines for noise control by enclosures and cabins |
| ISO 15739-2003 | 攝影.電子靜止圖象成像.噪聲測量 | Photography - Electronic still-picture imaging - Noise measurements |
| ISO 15744-2002 | 手持非電動工具.噪聲測量代碼.工程法(2級) | Hand-held non-electric power tools - Noise measurement code - Engineering method (grade 2) |
| ISO 16832-2006 | 聲學.利用類別法定義噪聲等級 | Acoustics - Loudness scaling by means of categories |
| ISO 17201-1 Technical Corrigendum 1-2009 | 聲學.射程內噪聲.第1部分:測量用槍口炸震的測定.技術勘誤1 | Acoustics - Noise from shooting ranges - Part 1: Determination of muzzle blast by measurement; Technical Corrigendum 1 |
| ISO 17201-1-2005 | 聲學.射程內噪聲.第1部分:槍口炸震的測定 | Acoustics - Noise from shooting ranges - Part 1: Determination of muzzle blast by measurement |
| ISO 17201-2-2006 | 聲學.射程內噪聲.第2部分:通過計算發射噪音和槍口炸震的評定 | Acoustics - Noise from shooting ranges - Part 2: Estimation of muzzle blast and projectile sound by calculation |
| ISO 17201-3-2010 | 聲學.射擊場的噪聲.第3部分:噪聲傳輸計算用指南 | Acoustics - Noise from shooting ranges - Part 3: Guidelines for sound propagation calculations |
| ISO 17201-4-2006 | 聲學.射程內噪聲.第4部分:發射噪音預報 | Acoustics - Noise from shooting ranges - Part 4: Prediction of projectile sound |
| ISO 17201-5-2010 | 聲學.射擊場的噪聲.第5部分:噪聲管理 | Acoustics - Noise from shooting ranges - Part 5: Noise management |
| ISO 1996-1-2003 | 聲學 環境噪聲的描述、測量和評價 第1部分:基本參量和評價方法 | Acoustics - Description, measurement and assessment of environmental noise - Part 1: Basic quantities and assessment procedures |
| ISO 1996-2-2007 | 聲學.環境噪聲的描述、測量和評估.第2部分:環境噪聲級別的測定 | Acoustics - Description, measurement and assessment of environmental noise - Part 2: Determination of environmental noise levels |
| ISO 1999-1990 | 聲學 職業性噪聲暴露的測定和噪聲引起的聽力損傷的估算 | Acoustics; determination of occupational noise exposure and estimation of noise-induced hearing impairment |
| ISO 20361-2007 | 液態泵和泵裝置.空氣噪聲試驗規則.2級和3級精度 | Liquid pumps and pump units - Noise test code - Grades 2 and 3 of accuracy |
| ISO 20906-2009 | 聲學.機場附近飛機噪聲的無人監測 | Acoustics - Unattended monitoring of aircraft sound in the vicinity of airports |
| ISO 2151-2004 | 聲學.壓縮機和真空泵的噪聲試驗規范.工程方法(2級) | Acoustics - Noise test code for compressors and vacuum pumps - Engineering method (Grade 2) |
| ISO 22897-2003 | 建筑物用玻璃.玻璃和空氣噪聲隔絕.產品描述和性能測定 | Glass in building - Glazing and airborne sound insulation - Product descriptions and determination of properties |
| ISO 230-5-2000 | 機床檢驗通則 第5部分:噪聲發射的測定 | Test code for machine tools - Part 5: Determination of the noise emisssion |
| ISO 2923 Technical Corrigendum 1-1997 | 聲學 船上的噪聲測量 技術勘誤1 | Acoustics - Measurement of noise on board vessels; Technical Corrigendum 1 |
| ISO 2923-1996 | 聲學 船上的噪聲測量 | Acoustics - Measurement of noise on board vessels |
| ISO 362-1-2007 | 加速道路車輛發出噪聲的測量.工程法.第1部分:M和N分類 | Measurement of noise emitted by accelerating road vehicles - Engineering method - Part 1: M and N categories |
| ISO 3740-2000 | 聲學 噪聲源聲功率級的測定 基本標準使用導則 | Acoustics - Determination of sound power levels of noise sources - Guidelines for the use basic standards |
| ISO 3741-2010 | 聲學.聲壓法測定噪聲源聲功率級.混響室精密法 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms |
| ISO 3743-1-2010 | 聲學.利用聲壓的噪聲源聲功率級和聲能級的測定.專用混響現場內小型可移動聲源的工程方法.第1部分:硬質圍墻 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room |
| ISO 3743-2-1994 | 聲學 聲壓法測定噪聲源聲功率級 混響聲場中小型可移動聲源的工程法 第2部分:專用混響試驗室法 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms |
| ISO 3745-2003 | 聲學.用聲壓法測定噪聲源聲功率級.消聲室和半消聲室精密法 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for anechoic and hemi-anechoic rooms |
| ISO 3822-1-1999 | 聲學 供水設施的裝置和設備發射的噪聲的實驗室測試 第1部分:測量方法 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement |
| ISO 3822-2-1995 | 聲學 供水設施的裝置和設備發射的噪聲的實驗室測試 第2部分:放水龍頭和混合閥的安裝和工作條件 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves |
| ISO 3822-3 AMD 1-2009 | 聲學.供水設施用裝置和設備發射噪聲的實驗室試驗.第3部分:管路閥門和器件的安裝和工作條作.修改件1 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances; Amendment 1 |
| ISO 3822-3-1997 | 聲學 供水設施的裝置和設備發射的噪聲的實驗室測試 第3部分:管路閥門和器件的安裝和工作條作 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances |
| ISO 3822-4-1997 | 聲學 供水設施的裝置和設備發射的噪聲的實驗室測試 第4部分:專用器件的安裝和工作條件 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances |
| ISO 389-4-1994 | 聲學 校正聽力設備的基準零級 第4部分:窄帶掩蔽噪聲基準級 | Acoustics - Reference zero for the calibration of audiometric equipment - Part 4: Reference levels for narrow-band masking noise |
| ISO 4412-1-1991 | 液壓傳動 空氣噪聲級測定的試驗規范 第1部分:泵 | Hydraulic fluid power; test code for determination of airborne noise levels; part 1: pumps |
| ISO 4412-2-1991 | 液壓傳動 空氣噪聲級測定的試驗規范 第2部分:馬達 | Hydraulic fluid power; test code for determination of airborne noise levels; part 2: motors |
| ISO 4412-3-1991 | 液壓傳動 空氣噪聲級測定的試驗規范 第3部分:泵 采用平行六面體傳聲器陣列的方法 | Hydraulic fluid power; test code for determination of airborne noise levels; part 3: pumps; method using a parallelepiped microphone array |
| ISO 5128-1980 | 聲學 汽車內的噪聲的測量 | Acoustics; Measurement of noise inside motor vehicles |
| ISO 5131-1996 | 聲學 農林拖拉機和機械 操作者位置處噪聲的測量 簡易法 | Acoustics - Tractors and machinery for agriculture and forestry - Measurement of noise at the operator's position - Survey method |
| ISO 5135-1997 | 聲學 在混響室中測定空調終端設備、空調終端單元、阻尼器和調節閥門的噪聲功率級 | Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room |
| ISO 6393-2008 | 土方機械.噪聲功率級的測定.靜態試驗條件 | Earth-moving machinery - Determination of sound power level - Stationary test conditions |
| ISO 6394 Technical Corrigendum 1-2009 | 土方機械.在操作者位置處測定運土機械發射的噪聲.穩態試驗條件,技術勘誤表1 | Earth-moving machinery - Determination of emission sound pressure level at operator's position - Stationary test conditions; Technical Corrigendum 1 |
| ISO 6798-1995 | 往復式內燃機 輻射的空氣噪聲測量 工程法和簡易法 | Reciprocating internal combustion engines - Measurement of emitted airborne noise - Engineering method and survey method |
| ISO 7216-1992 | 聲學 農林輪式拖拉機和自行機械 行駛時的噪聲的測量 | Acoustics; agricultural and forestry wheeled tractors and self-propelled machines; measurement of noise emitted when in motion |
| ISO 7235-2003 | 聲學.管道消音器和空氣界面裝置的實驗室測量步驟.插入損失、流動噪聲和總壓損失 | Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss |
| ISO 7574-1-1985 | 聲學 測定和檢驗機械及設備噪聲標定值的統計方法 第1部分:一般考慮和定義 | Acoustics; Statistical methods for determining and verifying stated noise emission values of machinery and equipment; Part 1 : General considerations and definitions |
| ISO 7574-2-1985 | 聲學 測定和檢驗機械及設備噪聲標定值的統計方法 第2部分:用于單個機械的方法 | Acoustics; Statistical methods for determining and verifying stated noise emission values of machinery and equipment; Part 2 : Methods for stated values for individual machines |
| ISO 7574-3-1985 | 聲學 測定和檢驗機械及設備噪聲標定值的統計方法 第3部分:用于機組的簡易(傳遞)法 | Acoustics; Statistical methods for determining and verifying stated noise emission values of machinery and equipment; Part 3 : Simple (transition) method for stated values for batches of machines |
| ISO 7574-4-1985 | 聲學 測定和檢驗機械及設備噪聲標定值的統計方法 第4部分:用于機組的方法 | Acoustics; statistical methods for determining and verifying stated noise emission values of machinery and equipment; part 4: methods for stated values for batches of machines |
| ISO 7960-1995 | 機床噪聲 木工機床的工作條件 | Airborne noise emitted by machine tools - Operating conditions for woodworking machines |
| ISO 8525-2008 | 機械工具發出的空氣噪聲.金屬切割機的運行條件 | Airborne noise emitted by machine tools - Operating conditions for metal-cutting machines |
| ISO 8528-10-1998 | 往復式內燃交流發電機組 第10部分:包絡面法測量空氣噪聲 | Reciprocating internal combustion engine driven alternating current generating sets - Part 10: Measurement of airborne noise by the enveloping surface method |
| ISO 9295-1988 | 聲學 計算機和辦公裝置發射的高頻噪聲的測量 | Acoustics; measurement of high-frequency noise emitted by computer and business equipment |
| ISO 9296-1988 | 聲學 計算機和辦公設備噪聲發射的申報值 | Acoustics; declared noise emission values of computer and business equipment |
| ISO 9568-1993 | 電影 影院、鑒定放映室及混錄棚的背景噪聲聲級 | Cinematography; background acoustic noise levels in theatres, review rooms and dubbing rooms |
| ISO 9614-1-1993 | 聲學 聲強法測定噪聲源聲功率級 第1部分:離散點測量法 | Acoustics; determination of sound power levels of noise sources using sound intensity; part 1: measurement at discrete points |
| ISO 9614-2-1996 | 聲學 聲強法測定噪聲源聲功率級 第2部分:掃描測量法 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning |
| ISO 9614-3-2002 | 聲學.利用聲音強度測定噪聲源功率級.第3部分:掃描測量精度法 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurements by scanning |
| ISO 9645-1990 | 聲學 運動中的雙輪機動自行車發射噪聲的測量 工程法 | Acoustics; measurement of noise emitted by two-wheeled mopeds in motion; engineering method |
| ISO 9902-1-2001 | 紡織機械 噪聲檢測規則 第1部分：通用要求 | Textile machinery - Noise test code - Part 1: Common requirements |
| ISO 9902-2 AMD 1-2009 | 紡織機械.噪聲試驗規則.第2部分:紡紗準備和紡紗機械.修改件1 | Textile machinery - Noise test code - Part 2: Spinning preparatory and spinning machinery; Amendment 1 |
| ISO 9902-2-2001 | 紡織機械 噪聲檢測規則 第2部分：紡紗準備和紡紗機械 | Textile machinery - Noise test code - Part 2: Spinning preparatory and spinning machinery |
| ISO 9902-3-2001 | 紡織機械 噪聲檢測規則 第3部分：無紡機械 | Textile machinery - Noise test code - Part 3: Nonwoven machinery |
| ISO 9902-4-2001 | 紡織機械 噪聲檢測規則 第4部分：紗線處理、纜索和繩索制造機械 | Textile machinery - Noise test code - Part 4: Yarn processing, cordage and rope manufacturing machinery |
| ISO 9902-5-2001 | 紡織機械 噪聲檢測規則 第5部分：織造和針織準備機械 | Textile machinery - Noise test code - Part 5: Weaving and knitting preparatory machinery |
| ISO 9902-6-2001 | 紡織機械 噪聲檢測規則 第6部分：織物制造機械 | Textile machinery - Noise test code - Part 6: Fabric manufacturing machinery |
| ISO 9902-7-2001 | 紡織機械 噪聲檢測規則 第7部分：染整機械 | Textile machinery - Noise test code - Part 7: Dyeing and finishing machinery |
| ISO/TR 11688-1-1995 | 聲學 低噪聲機器和設備設計的推薦實用規程 第1部分:計劃 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning |
| ISO/TR 11688-2-1998 | 聲學 低噪聲機器和設備設計的推薦實用規程 第2部分:低噪聲設計的物理工程說明 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design |
| ISO/TR 11690-3-1997 | 聲學 低噪聲機器工作間設計的推薦實用規程 第3部分:工作室中的聲傳播和噪聲預測 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 3: Sound propagation and noise prediction in workrooms |
| ISO/TS 15666-2003 | 聲學.應用社會調查和社會聲學調查評價噪聲煩惱度 | Acoustics - Assessment of noise annoyance by means of social and socio-acoustic surveys |
| ISO/TS 4869-5-2006 | 聲學.聽力保護.第5部分:與新的試驗?zāi)繕?biāo)對應的噪聲減弱估算方法 | Acoustics - Hearing protectors - Part 5: Method for estimation of noise reduction using fitting by inexperienced test subjects |
| 編號 | 中文名稱 | 英文名稱 |