| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| IEC 60055-1 AMD 1-2005 | 修改件1.額定電壓18/30KV及以下的銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜).第1部分:電纜及 | Amendment 1 - Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables) - Part 1: Tests on cables and their accessories |
| IEC 60055-1 Edition 5.1-2005 | 額定電壓18/30kV及以下銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜).第1部分:電纜及其附件的試 | Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables) - Part 1: Tests on cables and their accessories |
| IEC 60055-1-1997 | 額定電壓18/30kV及以下銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜) 第1部分:電纜及其附件試驗 | Paper-insulated metal-sheathed cabled for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables) - Part 1: Tests on cables and their accessories |
| IEC 60055-2 AMD 1-1989 | 額定電壓18/30kV及以下銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜) 第2部分:一般要求和結構要 | Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables); part 2: general and construction requirements; amendment No. 1 to IEC 60055-2:1981 |
| IEC 60055-2 AMD 2-2005 | 修改件2.額定電壓18/30KV及以下的銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜).第2部分:一般要 | Amendment 2 - Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables) - Part 2: General and construction requirements |
| IEC 60055-2-1981 | 額定電壓18/30kV及以下銅或鋁導線紙絕緣金屬護套電纜(不包括壓氣電纜和充油電纜) 第2部分:一般要求和結構要 | Paper-insulated metal-sheathed cabled for rated voltages up to 18/30 kV (with copper or aluminium conductors and excluding gas-pressure and oil-filled cables); Part 2: General and construction requirements |
| IEC 60104-1987 | 架空導線用鋁鎂硅合金導線 | Aluminium-magnesium-silicon alloy wire for overhead line conductors. |
| IEC 60105-1958 | 工業純鋁母線材料的推薦標準 | Recommendation for commercial-purity aluminium busbar material |
| IEC 60114 Corrigendum 1-1959 | 熱處理型鋁鎂硅系鋁合金母線材料的建議 | Recommendation for heat-treated aluminium alloy busbar material of the aluminium-magnesium-silicon type; Corrigendum 1 |
| IEC 60114-1959 | 熱處理型鋁鎂硅系鋁合金母線材料的建議 | Recommendation for heat-treated aluminium alloy busbar material of the aluminium-magnesium-silicon type |
| IEC 60121-1960 | 工業用電工退火鋁導線的建議 | Recommendation for commercial annealed aluminium electrical conductor wires |
| IEC 60317-0-3-2008 | 特種繞組線規范.第0-3部分:一般要求.漆包圓鋁線 | Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminium wire |
| IEC 60317-15-2004 | 特種繞組線規范.第15部分:180級聚酯酰亞胺漆包圓鋁線 | Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180 |
| IEC 60317-25 AMD 1-1997 | 特種繞組線規范 第25部分:200級聚酰胺-酰亞胺包敷聚酯或聚酯酰亞胺漆包圓鋁線 修改1 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200; Amendment 1 |
| IEC 60317-25 Edition 2.2-1997 | 特種繞組線規范.第25部分:涂覆聚酰胺-酰亞胺的聚酯或聚酯酰亞胺漆包圓鋁線.200級 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| IEC 60317-25-1990 | 特種繞組線規范 第25部分:200級聚酰胺-酰亞胺包敷聚酯或聚酯酰亞胺漆包圓鋁線 | Specifications for particular types of winding wires; part 25: polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| IEC 60384-18-1-2007 | 電子設備用固定電容器.第18-1部分:空白詳細規范.固體(MnO2)電解質表面安裝的固定鋁電解電容器.評定等級EZ | Fixed capacitors for use in electronic equipment - Part 18-1: Blank detail specification - Fixed aluminium electrolytic surface mount capacitors with solid (MnO<(Index)2>) electrolyte - Assessment level EZ |
| IEC 60384-18-2-2007 | 電子設備用固定電容器.第18-2部分:空白詳細規范.非固體電解質表面安裝的鋁電解固定電容器.評定等級EZ | Fixed capacitors for use in electronic equipment - Part 18-2: Blank detail specification - Fixed aluminium electrolytic surface mount capacitors with non-solid electrolyte - Assessment level EZ |
| IEC 60384-18-2007 | 電子設備用固定電容器.第18部分:分規范.固體(MnO2)和非固體電解質鋁電解固定表面安裝電容器 | Fixed capacitors for use in electronic equipment - Part 18: Sectional specification - Fixed aluminium electrolytic surface mount capacitors with solid (MnO<(Index)2>) and non-solid electrolyte |
| IEC 60384-25 Corrigendum 1-2006 | 電子設備用固定電容器.第25部分:分規范.采用導電聚合固體電解質的表面安裝固定鋁電解電容器 | Fixed capacitors for use in electronic equipment - Part 25: Sectional specification - Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte - Corrigendum 1 |
| IEC 60384-25-1-2006 | 電子設備用固定電容器.第25-1部分:空白詳細規范.帶傳導聚合固體電解質的表面安裝固定鋁制電解電容器.評定級 | Fixed capacitors for use in electronic equipment - Part 25-1: Blank detail specification - Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte - Assessment level EZ |
| IEC 60384-25-2006 | 電子設備用固定電容器.第25部分:分規范.帶傳導聚合固體電解質的表面安裝固定鋁制電解電容器 | Fixed capacitors for use in electronic equipment - Part 25: Sectional specification - Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte |
| IEC 60384-4-1-2007 | 電子設備用固定電容器.第4-1部分:空白詳細規范.非固體電解質的鋁電解電容器.評定等級EZ | Fixed capacitors for use in electronic equipment - Part 4-1: Blank detail specification - Fixed aluminium electrolytic capacitors with non-solid electrolyte - Assessment level EZ |
| IEC 60384-4-2-2007 | 電子設備用固定電容器.第4-2部分:空白詳細規范.固體(MnO2)電解質的鋁電解電容器.評定等級EZ | Fixed capacitors for use in electronic equipment - Part 4-2: Blank detail specification - Fixed aluminium electrolytic capacitors with solid (MnO<(Index)2>) electrolyte - Assessment level EZ |
| IEC 60384-4-2007 | 電子設備用固定電容器.第4部分:分規范.固體(MnO2)和非固體電解質的鋁電解電容器 | Fixed capacitors for use in electronic equipment - Part 4: Sectional specification - Aluminium electrolytic capacitors with solid (MnO<(Index)2>) and non-solid electrolyte |
| IEC 60889-1987 | 架空導線用硬拉鋁線 | Hard-drawn aluminium wire for overhead line conductors. |
| IEC 61232-1993 | 電工用鋁包鋼線 | Aluminium-clad steel wires for electrical purposes |
| IEC 61545-1996 | 連接器件 任何材料的夾緊裝置中的鋁線和鋁包夾緊裝置中的銅線的連接器件 | Connecting devices - Devices for the connection of aluminium conductors in clamping units of any material and copper conductors in aluminium bodied clamping units |
| IEC 62004-2007 | 架空導線用耐熱鋁合金導線 | Thermal resistant aluminium alloy wire for overhead line conductor |
| IEC/TR2 61394-1997 | 架空線路 鋁、鋁合金及鋼心導線用脂的特性 | Overhead lines - Characteristics of greases for aluminium, aluminium alloy and steel bare conductors |
| ISO 10042 Technical Corrigendum 1-2006 | 焊接.鋁和鋁合金的弧焊接頭.缺陷質量分級.技術勘誤1 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections; Technical Corrigendum 1 |
| ISO 10042-2005 | 焊接.鋁和鋁合金的弧焊接頭.缺陷質量分級 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections |
| ISO 10049-1992 | 鋁合金鑄件 目視法評定針孔 | Aluminium alloy castings; visual method for assessing the porosity |
| ISO 10074-1994 | 鋁和鋁合金硬質陽極氧化膜規范 | Specification for hard anodic oxidation coatings on aluminium and its alloys |
| ISO 10081-1-2003 | 致密定型耐火制品的分類.第1部分:鋁-硅酸鹽產品 | Classification of dense shaped refractory products - Part 1: Alumina-silica |
| ISO 10136-4-1993 | 玻璃和玻璃器皿 萃取溶液的分析 第4部分:用分子吸收光譜法測定氧化鋁 | Glass and glassware; analysis of extract solutions; part 4: determination of aluminium oxide by molecular absorption spectrometry |
| ISO 10142-1996 | 鋁生產用碳素材料 煅燒焦 用實驗室振動磨測定粒度穩定性 | Carbonaceous materials for use in the production of aluminium - Calcined coke - Determination of grain stability using a laboratory vibration mill |
| ISO 10143-1995 | 鋁生產用碳素材料 電極用煅燒焦 顆粒電阻率的測定 | Carbonaceous materials for the production of aluminium - Calcined coke for electrodes - Determination of the electrical resistivity of granules |
| ISO 10213-1991 | 鋁土礦石 總鐵含量的測定 三氯化鈦還原法 | Aluminium ores; determination of total iron content; titanium trichloride reduction method |
| ISO 10215-1992 | 陽極氧化鋁和鋁合金 陽極氧化膜圖像清晰度的目視測定 圖表比例尺法 | Anodized aluminium and aluminium alloys; visual determination of image clarity of anodic oxidation coatings; chart scale method |
| ISO 10216-1992 | 陽極氧化鋁和鋁合金 陽極氧化膜圖像清晰度儀器測定 儀器法 | Anodized aluminium and aluminium alloys; instrumental determination of image clarity of anodic oxidation coatings; instrumental method |
| ISO 10226-1991 | 鋁土礦石 取樣偏差的檢驗方法 | Aluminium ores; experimental methods for checking the bias of sampling |
| ISO 10236-1995 | 鋁生產用碳素材料 電極用生焦和煅燒焦 松(緊裝)密度的測定 | Carbonaceous materials for the production of aluminium - Green coke and calcined coke for electrodes - Determination of bulk density (tapped) |
| ISO 10237-1997 | 鋁生產用碳素材料 煅燒焦 殘余氫含量的測定 | Carbonaceous materials for use in the production of aluminium - Calcined coke - Determination of residual-hydrogen content |
| ISO 10238-1999 | 鋁生產用碳素材料 電極用瀝青 儀器法測定硫含量 | Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Determination of sulfur content by an instrumental method |
| ISO 10277-1995 | 鋁土礦石 取樣精度的檢驗方法 | Aluminium ores - Experimental methods for checking the precision of sampling |
| ISO 10461 AMD 1-2006 | 儲氣瓶.無縫鋁合金儲氣瓶.定期檢驗和試驗 | Gas cylinders - Seamless aluminium-alloy gas cylinders - Periodic inspection and testing |
| ISO 10461-2005 | 儲氣瓶.無縫鋁合金儲氣瓶.定期檢驗和試驗 | Gas cylinders - Seamless aluminium-alloy gas cylinders - Periodic inspection and testing |
| ISO 10478-1994 | 石油產品 中間燃份油中的鋁和硅的測定 感應耦合等離子發射和原子吸收光譜法 | Petroleum products - Determination of aluminium and silicon in fuel oils - Inductively coupled plasma emission and atomic absorption spectroscopy methods |
| ISO 105-X01-1993 | 紡織品 色牢度試驗 第X01部分:耐碳化色牢度:氯化鋁法 | Textiles; tests for colour fastness; part X01: colour fastness to carbonizing: aluminium chloride |
| ISO 10546-1993 | 化學轉化膜 鋁及鋁合金上瓢洗和未瓢洗的鉻酸鹽轉化膜 | Chemical conversion coatings; rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys |
| ISO 10566-1994 | 水質 鋁的測定 鄰苯二酚紫光度法 | Water quality - Determination of aluminium - Spectrometric method using pyrocatechol violet |
| ISO 10985-2009 | 輸液瓶和注射管用鋁-塑合成蓋.要求和試驗方法 | Caps made of aluminium-plastics combinations for infusion bottles and injection vials - Requirements and test methods |
| ISO 11040-3-1993 | 帶藥注射器 第3部分:齒科局部麻醉藥茼用鋁蓋 | Prefilled syringes; part 3: aluminium caps for dental local anaesthetic cartridges |
| ISO 11126-7 Technical Corrigendum 1-1999 | 涂裝油漆和有關產品前鋼材預處理 噴射清理用非金屬磨料的技術要求 第7部分:熔融氧化鋁 技術勘誤1 | Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide; Technical Corrigendum 1 |
| ISO 11126-7-1995 | 涂裝油漆和有關產品前鋼材預處理 噴射清理用非金屬磨料的技術要求 第7部分:熔融氧化鋁 | Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide |
| ISO 1118-1978 | 鋁和鋁合金 鈦含量的測定 鉻變酸分光光度法 | Aluminium and aluminium alloys; Determination of titanium; Spectrophotometric chromotropic acid method |
| ISO 11412-1998 | 鋁生產用碳素材料 煅燒焦 水分測定 | Carbonaceous materials for the production of aluminium - Calcined coke - Determination of water content |
| ISO 115-2003 | 重熔用非鋁合金錠.分類及成分 | Unalloyed aluminium ingots for remelting - Classification and composition |
| ISO 11678-1996 | 農業排灌設備 鋁制灌溉管 | Agricultural irrigation equipment - Aluminium irrigation tubes |
| ISO 1169-2006 | 鋅合金.鋁含量的測定.滴定法 | Zinc alloys - Determination of aluminium content - Titrimetric method |
| ISO 11713-2000 | 鋁生產用碳素材料 陰極碳塊和焙燒陽極 室溫下電阻率的測定 | Carbonaceous materials used in the production of aluminium - Cathode blocks and baked anodes - Determination of electrical resistivity at ambient temperature |
| ISO 11846-1995 | 金屬與合金的腐蝕 溶解熱處理鋁合金的耐晶間腐蝕性的測定 | Corrosion of metals and alloys - Determination of resistance to intergranular corrosion of solution heat-treatable aluminium alloys |
| ISO 11881 Technical Corrigendum 1-1999 | 金屬與合金的腐蝕 鋁合金的剝落腐蝕試驗 技術勘誤1 | Corrosion of metals and alloys - Exfoliation corrosion testing of aluminium alloys; Technical Corrigendum 1 |
| ISO 11881-1999 | 金屬與合金的腐蝕 鋁合金的剝落腐蝕試驗 | Corrosion of metals and alloys - Exfoliation corrosion testing of aluminium alloys |
| ISO 12020-1997 | 水質 鋁的測定 原子吸收光譜法 | Water quality - Determination of aluminium - Atomic absorption spectrometric methods |
| ISO 12103-2-1997 | 道路車輛 用于濾清器評價的粉塵試驗 第2部分:氧化鋁試驗粉塵 | Road vehicles - Test dust for filter evaluation - Part 2: Aluminium oxide test dust |
| ISO 12215-3-2002 | 小型船舶.船體結構和船材尺寸.第3部分:材料:鋼,鋁合金,木料及其它材料 | Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| ISO 1232-1976 | 主要用于鋁生產的氧化鋁 二氧化硅含量的測定 鉬藍光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of silica content; Reduced molybdosilicate spectrophotometric method |
| ISO 1247 AMD 1-1982 | 色漆用鋁顏料 修改1 | Aluminium pigments for paints; amendment 1 |
| ISO 1247-1974 | 色漆用鋁顏料 | Aluminium pigments for paints |
| ISO 12977-1999 | 鋁生產用碳素材料 電極用瀝青 揮發分的測定 | Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Determination of volatile matter content |
| ISO 12979-1999 | 鋁生產用碳素材料 電極用瀝青 喹啉不溶物中C/H比的測定 | Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Determination of C/H ratio in the quinoline-insoluble fraction |
| ISO 12980-2000 | 鋁生產用碳素材料 電極用生焦和煅燒焦 X射線熒光分析 | Carbonaceous materials used in the production of aluminium - Green coke and calcined coke for electrodes - Analysis using an X-ray fluorescence method |
| ISO 12981-1-2000 | 鋁生產用碳素材料 煅燒焦 對二氧化碳反應性的測定 第1部分:失重法 | Carbonaceous materials used in the production of aluminium - Calcined coke; Determination of the reactivity to carbon dioxide - Part 1: Loss in mass method |
| ISO 12982-1-2000 | 鋁生產用碳素材料 煅燒焦 對空氣反應性的測定 第1部分:灼燒溫度法 | Carbonaceous materials used in the production of aluminium - Calcined coke; Determination of the reactivity to air - Part 1: Ignition temperature method |
| ISO 12984-2000 | 鋁生產用碳素材料 煅燒焦 粒度分布的測定 | Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of particle size distribution |
| ISO 12985-1-2000 | 鋁生產用碳素材料 焙燒陽極和陰極碳塊 第1部分:用尺寸法測定表觀密度 | Carbonaceous materials used in the production of aluminium - Baked anodes and cathode blocks - Part 1: Determination of apparent density using a dimensions method |
| ISO 12985-2-2000 | 鋁生產用碳素材料 焙燒陽極和陰極碳塊 第2部分:用靜流法測定表觀密度和開口孔隙率 | Carbonaceous materials used in the production of aluminium - Baked anodes and cathode blocks - Part 2: Determination of apparent density and of open porosity using a hydrostatic method |
| ISO 12986-1-2000 | 鋁生產用碳素材料 預焙陽極和陰極碳塊 第1部分:用三點法測定抗彎強度/剪切強度 | Carbonaceous materials used in the production of aluminium - Prebaked anodes and cathode blocks - Part 1: Determination of bending/shear strength by a three-point method |
| ISO 12986-2-2005 | 鋁生產用碳素材料.預焙陽極和陰極碳塊.第2部分:用四點法測定抗彎強度 | Carbonaceous materials used in the production of aluminium - Prebaked anodes and cathode blocks - Part 2: Determination of flexural strength by the four-point method |
| ISO 12987-2004 | 鋁制品用碳質材料.陽極、陰極塊、側壁磚和烤灌糊.使用比較法進行熱傳導性的測定 | Carbonaceous materials for the production of aluminium - Anodes, cathodes blocks, sidewall blocks and baked ramming pastes - Determination of the thermal conductivity using a comparative method |
| ISO 12988-1-2000 | 鋁生產用碳素材料 焙燒陽極 二氧化碳反應性的測定 第1部分:失重法 | Carbonaceous materials used in the production of aluminium - Baked anodes - Determination of the reactivity to carbon dioxide - Part 1: Loss in mass method |
| ISO 12988-2-2004 | 鋁生產用碳素材料.焙燒陽極.二氧化碳反應性的測定.第2部分:熱解重量分析法 | Carbonaceous materials used in the production of aluminium - Baked anodes - Determination of the reactivity to carbon dioxide - Part 2: Thermogravimetric method |
| ISO 12989-1-2000 | 鋁生產用碳素材料 焙燒陽極和部碳塊 空氣反應性的測定 第1部分:失重法 | Carbonaceous materials used in the production of aluminium - Baked anodes and sidewall blocks - Determination of the reactivity to air - Part 1: Loss in mass method |
| ISO 12989-2-2004 | 鋁生產用碳素材料.焙燒陽極和部碳塊.空氣反應性的測定.第2部分:熱重分析法 | Carbonaceous materials used in the production of aluminium - Baked anodes and sidewall blocks - Determination of the reactivity to air - Part 2: Thermogravimetric method |
| ISO 13770-1997 | 鋁合金氣瓶 避免瓶頸和瓶肩裂紋的操作要求 | Aluminium alloy gas cylinders - Operational requirements for avoidance of neck and shoulder cracks |
| ISO 13805-1999 | 鋁上釉瓷和搪瓷 在電解液作用下測定鋁上瓷層附著力(剝落試驗) | Vitreous and porcelain enamels for aluminium - Determination of the adhesion of enamels on aluminium under the action of electrolytic solution (spall test) |
| ISO 13919-2-2001 | 焊接 電子束和激光束焊接接頭 缺陷質量等級指南 第2部分：鋁及其可焊合金 | Welding - Electron and laser beam welded joints; Guidance on quality levels for imperfections - Part 2: Aluminium and its weldable alloys |
| ISO 14420-2005 | 鋁生產用碳質產品.焙燒陽極和成形碳產品.線性熱膨脹系數的測定 | Carbonaceous products for the production of aluminium - Baked anodes and shaped carbon products - Determination of the coefficient of linear thermal expansion |
| ISO 14422-1999 | 鋁生產用碳素材料 冷壓糊料 取樣方法 | Carbonaceous materials used in the production of aluminium - Cold-ramming pastes - Methods of sampling |
| ISO 14427-2004 | 鋁生產用碳質材料.冷和微熱搗實糊料.非烤試驗樣品的制備和壓縮后表觀密度的測定 | Carbonaceous materials used in the production of aluminium - Cold and tepid ramming pastes - Preparation of unbaked test specimens and determination of apparent density after compaction |
| ISO 14428-2005 | 鋁生產用碳素材料.冷和微溫沖壓漿料.烘烤時的膨脹/收縮 | Carbonaceous materials for the production of aluminium - Cold and tepid ramming pastes - Expansion/shrinkage during baking |
| ISO 14435-2005 | 鋁生產用含碳材料.石油焦.用感應耦合等離子體原子發射光譜測定法測定痕量金屬 | Carbonaceous materials for the production of aluminium - Petroleum coke - Determination of trace metals by inductively coupled plasma atomic emission spectrometry |
| ISO 14676-1997 | 粘合劑 鋁表面處理工藝有效性的評估 用導向托輥法作濕剝離試驗 | Adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium - Wet-peel test by floating-roller method |
| ISO 14713-1999 | 鋼結構腐蝕防護 鋅和鋁鍍層 指南 | Protection against corrosion of iron and steel in structures - Zinc and aluminium coatings - Guidelines |
| ISO 14788-2005 | 連續熱浸鍍鋅(5%)鋁合金涂層鋼薄板 | Continuous hot-dip zinc-5% aluminium alloy coated steel sheet |
| ISO 15329-2006 | 金屬和合金的腐蝕.熱處理鋁合金的粒間腐蝕易感性評價的陽極試驗 | Corrosion of metals and alloys - Anodic test for evaluation of intergranular corrosion susceptibility of heat-treatable aluminium alloys |
| ISO 15379-1-2004 | 鋁生產用碳質材料.陰極塊材料.第1部分:壓力作用下由于鈉滲透引起的膨脹的測定 | Carbonaceous materials for the production of aluminium - Cathode block materials - Part 1: Determination of the expansion due to sodium penetration with application of pressure |
| ISO 15379-2-2004 | 鋁生產用碳質材料.陰極塊材料.第2部分:無壓力作用下由于鈉滲透引起的膨脹的測定 | Carbonaceous materials for the production of aluminium - Cathode block materials - Part 2: Determination of the expansion due to sodium penetration without application of pressure |
| ISO 15546-2007 | 石油和天然氣工業.鋁合金鉆桿 | Petroleum and natural gas industries - Aluminium alloy drill pipe |
| ISO 15547-2-2005 | 石油、石化和天然氣工業.板式熱交換器.第2部分:銅焊鋁板熱交換器 | Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers |
| ISO 15614-2 Technical Corrigendum 1-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第2部分:鋁及其合金的電弧焊接.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys; Technical Corrigendum 1 |
| ISO 15614-2-2005 | 金屬材料焊接程序的規范和鑒定.焊接過程試驗.第2部分:鋁和鋁合金電弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys |
| ISO 15614-4 Technical Corrigendum 1-2007 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第4部分:鋁鑄件的精工焊接.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings; Technical Corrigendum 1 |
| ISO 15614-4-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第4部分:鋁鑄件的精工焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings |
| ISO 15906-2007 | 鋁生產用碳質材料.焙燒陽極.空氣滲透率測定 | Carbonaceous materials for the production of aluminium - Baked anodes - Determination of the air permeability |
| ISO 1617-1976 | 主要用于鋁生產的氧化鋁 鈉含量的測定 火焰發射分光光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of sodium content; Flame emission spectrophotometric method |
| ISO 1618-1976 | 主要用于鋁生產的氧化鋁 釩含量的測定 N-苯甲酰-N-苯胲光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of vanadium content; N-Benzoyl-N-phenylhydroxylamine photometric method |
| ISO 16962-2005 | 表面化學分析.用輝光放電光發射光譜測定法分析鋅和/或鋁基金屬涂層 | Surface chemical analysis - Analysis of zinc- and/or aluminium-based metallic coatings by glow-discharge optical-emission spectrometry |
| ISO 17499-2006 | 鋁生產用碳質材料.用等效溫度表示的烘烤等級的測定 | Carbonaceous materials used in the production of aluminium - Determination of baking level expressed by equivalent temperature |
| ISO 17500-2006 | 原鋁生產用氧化鋁.磨損指數的測定 | Aluminium oxide used for the production of primary aluminium - Determination of attrition index |
| ISO 17544-2004 | 鋁生產用碳質材料.冷和微熱搗實糊料.非烤糊料的可壓實性測定 | Carbonaceous materials used in the production of aluminium - Cold and tepid ramming pastes - Determination of rammability of unbaked pastes |
| ISO 17615 Technical Corrigendum 1-2008 | 鋁和鋁合金.再熔煉用合金鑄錠.規范.技術勘誤1 | Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications; Technical Corrigendum 1 |
| ISO 17615-2007 | 鋁和鋁合金.重熔用合金鑄錠.規范 | Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications |
| ISO 1784-1976 | 鋁合金 鋅含量的測定 EDTA滴定法 | Aluminium alloys; Determination of zinc; EDTA titrimetric method |
| ISO 17925-2004 | 鋼上鋅和/或鋁基涂層.單位面積涂層質量和化學組分的測定.重量分析法、感應耦合等離子體原子輻射光譜測定法 | Zinc and/or aluminium based coatings on steel - Determination of coating mass per unit area and chemical composition - Gravimetry, inductively coupled plasma atomic emission spectrometry and flame atomic absorption spectrometry |
| ISO 18273-2004 | 焊接消耗品.鋁和鋁合金焊接用焊絲電極、金屬絲和棒材.分類 | Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification |
| ISO 18515-2007 | 鋁生產用含碳材料.陰極塊和焙燒陽極.耐壓強度的測定 | Carbonaceous materials for the production of aluminium - Cathode blocks and baked anodes - Determination of compressive strength |
| ISO 18594-2007 | 電阻點焊接、電阻凸焊和電阻縫隙焊接.測定鋁和鋼材料的躍遷電阻 | Resistance spot-, projection- and seam-welding - Method for determining the transition resistance on aluminium and steel material |
| ISO 18595-2007 | 電阻焊接.鋁和鋁合金的點焊.可焊接性、焊接和測試 | Resistance welding - Spot welding of aluminium and aluminium alloys - Weldability, welding and testing |
| ISO 1965-1973 | 航空器鋁電纜的鋁壓接端子 | Aluminium terminal ends for crimping to aircraft aluminium electrical cables |
| ISO 20202-2004 | 鋁生產用碳質材料.冷和微熱搗實材料.烘烤試樣的制備和烘烤時損失的測定 | Carbonaceous materials used in the production of aluminium - Cold and tepid ramming pastes - Preparation of baked test pieces and determination of loss on baking |
| ISO 20203-2005 | 鋁生產中使用的碳素材料.煅燒焦炭.用X-射線衍射法測定煅燒石油焦的晶體粒度 | Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction |
| ISO 2063-2005 | 熱噴鍍.金屬涂層和其他無機覆層.鋅、鋁及其合金 | Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys |
| ISO 2069-1976 | 主要用于鋁生產的氧化鋁 鈣含量的測定 火焰原子吸收法 | Aluminium oxide primarily used for the production of aluminium; Determination of calcium content; Flame atomic absorption method |
| ISO 2070-1997 | 主要用于鋁生產的氧化鋁 鈣含量的測定 | Aluminium oxide primarily used for the production of aluminium - Determination of calcium content |
| ISO 20703-2006 | 氣瓶.可再充裝的焊接鋁合金氣瓶.設計、結構和試驗 | Gas cylinders - Refillable welded aluminium-alloy cylinders - Design, construction and testing |
| ISO 2071-1976 | 主要用于鋁生產的氧化鋁 鋅含量的測定 火焰原子吸收法 | Aluminium oxide primarily used for the production of aluminium; Determination of zinc content; Flame atomic absorption method |
| ISO 2072-1981 | 主要用于鋁生產的氧化鋁 鋅含量的測定 PAN光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of zinc content; PAN photometric method |
| ISO 2073-1976 | 主要用于鋁生產的氧化鋁 分析用溶液的制備 加壓下的鹽酸反應法 | Aluminium oxide primarily used for the production of aluminium; Preparation of solution for analysis; Method by hydrochloric acid attack under pressure |
| ISO 2085-1976 | 鋁和鋁合金的陽極氧化 陽極氧化膜的連續性檢驗 硫酸銅試驗 | Anodizing of aluminium and its alloys; Check of continuity of thin anodic oxide coatings; Copper sulphate test |
| ISO 209-2007 | 鋁和鋁合金.化學成分 | Aluminium and aluminium alloys - Chemical composition |
| ISO 2106 AMD 1-1983 | 鋁和鋁合金的陽極氧化 陽極氧化膜單位面積質量(表面密度)的測定 重量法 修改1 | Anodizing of aluminium and its alloys; determination of surface density of anodic oxide coatings; gravimetric method; amendment 1 |
| ISO 2106-1982 | 鋁和鋁合金的陽極氧化 陽極氧化膜單位面積質量(表面密度)的測定 重量法 | Anodizing of aluminium and its alloys; Determination of mass per unit area (surface density) of anodic oxide coatings; Gravimetric method |
| ISO 2107-2007 | 鋁和鋁合金.鍛造制品.回火號 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| ISO 21079-1-2008 | 包含氧化鋁、氧化鋯和硅石的耐火材料的化學分析.包含5%～45%ZrO<指數2>的耐火材料(可選擇X射線熒光法).第1 | Chemical analysis of refractories containing alumina, zirconia and silica - Refractories containing 5 % to 45 % of ZrO<(Index)2> (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents and dissolution |
| ISO 21079-2-2008 | 包含氧化鋁、氧化鋯和硅石的耐火材料的化學分析.包含5%～45%ZrO<指數2>的耐火材料(可選擇X射線熒光法).第2 | Chemical analysis of refractories containing alumina, zirconia, and silica - Refractories containing 5 % to 45 % of ZrO<(Index)2> (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis |
| ISO 21079-3-2008 | 包含氧化鋁、氧化鋯和硅石的耐火材料用化學分析.包含5%～45%ZrO<指數2>的耐火材料(可選擇X射線熒光法).第3 | Chemical analysis of refractories containing alumina, zirconia, and silica - Refractories containing 5 % to 45 % of ZrO<(Index)2> (alternative to the X-ray fluorescence method) - Part 3: Flame atomic absorption spectrophotometry (FAAS) and inductively coupled plasma emission spectrometry (ICP-AES) |
| ISO 2128-1976 | 鋁和鋁合金的陽極氧化 陽極氧化膜厚度的測定 分光束顯微鏡無損測定法 | Anodizing of aluminium and its alloys; Determination of thickness of anodic oxide coatings; Non-destructive measurement by split-beam microscope |
| ISO 2135-1984 | 鋁和鋁合金的陽極氧化 用人工燈測定著色陽極氧化膜耐光性的加速耐候試驗 | Anodizing of aluminium and its alloys; Accelerated test of light fastness of coloured anodic oxide coatings using artificial light |
| ISO 2143-1981 | 鋁和鋁合金的陽極氧化 封孔后的陽極氧化膜吸收能力損失的評估 酸處理后的染斑試驗 | Anodizing of aluminium and its alloys; Estimation of loss of absorptive power of anodic oxide coatings after sealing; Dye spot test with prior acid treatment |
| ISO 21587-1-2007 | 硅酸鋁耐火材料的化學分析(可選擇X射線熒光法).第1部分:儀器、試劑、硅石的分解和重量測定 | Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents, dissolution and gravimetric silica |
| ISO 21587-2-2007 | 硅酸鋁耐火材料的化學分析(可選擇X射線熒光法).第2部分:濕化學分析 | Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis |
| ISO 21587-3-2007 | 硅酸鋁耐火材料的化學分析(可選擇X射線熒光法).第3部分:感應耦合等離子體和原子吸收光譜測量法 | Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 3: Inductively coupled plasma and atomic absorption spectrometry methods |
| ISO 21687-2007 | 鋁生產用含碳材料.以氮作為分析氣體用比重測量法(測定體積的)測定密度.固體材料 | Carbonaceous materials used in the production of aluminium - Determination of density by gas pyknometry (volumetric) using helium as the analysis gas - Solid materials |
| ISO 22779-2006 | 金屬涂層.鋁的物理蒸汽沉積涂層法.規范和試驗方法 | Metallic coatings - Physical vapour-deposited coatings of aluminium - Specification and test methods |
| ISO 2297-1973 | 鋁和鋁合金的化學分析 鎂的絡合滴定法測定 | Chemical analysis of aluminium and its alloys; Complexometric determination of magnesium |
| ISO 23202-2006 | 鋁制產品用氧化鋁.經過一個20微米孔隙篩的粒子的測定 | Aluminium oxide used for the production of aluminium - Determination of particles passing a 20 micrometre aperture sieve |
| ISO 2367-1972 | 天然和人造冰晶石 鋁含量的測定 8-羥基喹啉重量法 | Cryolite (natural and artificial); Determination of aluminium content; 8- Hydroxyquinoline gravimetric method |
| ISO 2376-1972 | 鋁和鋁合金的陽極氧化 絕緣性能的擊穿電勢檢查法 | Anodization (anodic oxidation) of aluminium and its alloys; Insulation check by measurement of breakdown potential |
| ISO 2378-1972 | 鋁合金冷硬鑄件 參比試棒 | Aluminium alloy chill castings; Reference test bar |
| ISO 2379-1972 | 鋁合金砂模鑄件 參比試棒 | Aluminium alloy sand castings; Reference test bar |
| ISO 2828-1973 | 主要用于鋁生產的氧化鋁 氟含量的測定 茜素配位酮和氯化鑭分光光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of fluorine content; Alizarin complexone and lanthanum chloride spectrophotometric method |
| ISO 2829-1973 | 主要用于鋁生產的氧化鋁 磷含量的測定 還原磷鉬酸鹽分光光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of phosphorus content; Reduced phosphomolybdate spectrophotometric method |
| ISO 2830-1973 | 天然和人造冰晶石 鋁含量的測定 原子吸收法 | Cryolite, natural and artificial; Determination of aluminium content; Atomic absorption method |
| ISO 2865 Technical Corrigendum 1-1991 | 主要用于鋁生產的氧化鋁 硼含量的測定 姜黃素分光光度法 技術勘誤1 | Aluminium oxide primarily used for the production of aluminium; determination of boron content; curcumin spectrophotometric method; technical corrigendum 1 |
| ISO 2865-1973 | 主要用于鋁生產的氧化鋁 硼含量的測定 姜黃素分光光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of boron content; Curcumin spectrophotometric method |
| ISO 2926-2005 | 主要用于鋁生產的氧化鋁.45 μm至150 μm范圍內的粒度分析.電刻篩分法 | Aluminium oxide used for the production of primary aluminium - Particle size analysis for the range 45 μm to 150 μm - Method using electroformed sieves |
| ISO 2927-1973 | 主要用于鋁生產的氧化鋁 取樣 | Aluminium oxide primarily used for the production of aluminium; Sampling |
| ISO 2931-1983 | 鋁和鋁合金的陽極氧化 用導納或阻抗測量法評定陽極氧化膜的封孔質量 | Anodizing of aluminium and its alloys; Assessment of quality of sealed anodic oxide coatings by measurement of admittance or impedance |
| ISO 2961-1974 | 主要用于鋁生產的氧化鋁 吸附指數的測定 | Aluminium oxide primarily used for the production of aluminium; Determination of an adsorption index |
| ISO 3110-1975 | 銅合金 合金元素鋁含量的測定 容量法 | Copper alloys; Determination of aluminium as alloying element; Volumetric method |
| ISO 3210-1983 | 鋁和鋁合金的陽極氧化 磷-鉻酸法評定陽極氧化膜的封孔質量 | Anodizing of aluminium and its alloys; Assessment of quality of sealed anodic oxide coatings by measurement of the loss of mass after immersion in phosphoric-chromic acid solution |
| ISO 3211-1977 | 鋁和鋁合金的陽極氧化 陽極氧化膜抗變形破裂性的評定 | Anodizing of aluminium and its alloys; Assessment of resistance of anodic oxide coatings to cracking by deformation |
| ISO 3255-1974 | 鎂和鎂合金 鋁含量的測定 鉻天青S光度法 | Magnesium and magnesium alloys; Determination of aluminium; Chromazurol S photometric method |
| ISO 3256-1977 | 鋁和鋁合金 鎂含量的測定 原子吸收分光光度法 | Aluminium and aluminium alloys; Determination of magnesium; Atomic absorption spectrophotometric method |
| ISO 3262-16-2000 | 涂料用填充劑 規范和試驗方法 第16部分:氫氧化鋁 | Extenders for paints - Specifications and methods of test - Part 16: Aluminium hydroxides |
| ISO 3262-18-2000 | 涂料用填充劑 規范和試驗方法 第18部分:沉淀硅鋁酸鈉 | Extenders for paints - Specifications and methods of test - Part 18: Precipitated sodium aluminium silicate |
| ISO 3390-1976 | 主要用于鋁生產的氧化鋁 錳含量的測定 火焰原子吸收法 | Aluminium oxide primarily used for the production of aluminium; Determination of manganese content; Flame atomic absorption method |
| ISO 3393-1976 | 工業用天然及人造冰晶石和氟化鋁 含水量的測定 重量法 | Cryolite, natural and artificial, and aluminium fluoride for industrial use; Determination of moisture content; Gravimetric method |
| ISO 3429-1976 | 主要用于鋁生產的氟化鈉 鐵含量的測定 1,10-菲羅啉光度法 | Sodium fluoride primarily used for the production of aluminium; Determination of iron content; 1,10- Phenanthroline photometric method |
| ISO 3430-1976 | 主要用于鋁生產的氟化鈉 二氧化硅含量的測定 還原硅鉬酸鹽分光光度法 | Sodium fluoride primarily used for the production of aluminium; Determination of silica content; Reduced molybdosilicate spectrophotometric method |
| ISO 3431-1976 | 主要用于鋁生產的氟化鈉 可溶性硫酸鹽含量的測定 濁度測定法 | Sodium fluoride primarily used for the production of aluminium; Determination of soluble sulphates content; Turbidimetric method |
| ISO 3566-1976 | 主要用于鋁生產的氟化鈉 氯化物含量的測定 濁度測定法 | Sodium fluoride primarily used for the production of aluminium; Determination of chlorides content; Turbidimetric method |
| ISO 3613-2000 | 鋅、鎘、鋁鋅合金和鋅鋁合金的鉻酸鹽轉化膜 試驗方法 | Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods |
| ISO 3620-1994 | 攝影.沖洗藥品.十二水硫酸鋁鉀規范 | Photography - Processing chemicals - Specifications for aluminium potassium sulfate |
| ISO 3978-1976 | 鋁和鋁合金 鉻含量的測定 萃取二苯卡巴肼分光光度法 | Aluminium and aluminium alloys; Determination of chromium; Spectrophotometric method using diphenylcarbazide, after extraction |
| ISO 3979-1977 | 鋁和鋁合金 鎳含量的測定 丁二酮肟分光光度法 | Aluminium and aluminium alloys; Determination of nickel; Spectrophotometric method using dimethylglyoxime |
| ISO 3980-1977 | 鋁和鋁合金 銅含量的測定 原子吸收分光光度法 | Aluminium and aluminium alloys; Determination of copper; Atomic absorption spectrophotometric method |
| ISO 3981-1977 | 鋁和鋁合金 鎳含量的測定 原子吸收分光光度法 | Aluminium and aluminium alloys; Determination of nickel; Atomic absorption spectrophotometric method |
| ISO 4139-1979 | 硅鐵合金 鋁含量的測定 火焰原子吸收光譜法 | Ferrosilicon; determination of aluminium content; Flame atomic absorption spectrometric method |
| ISO 4192-1981 | 鋁和鋁合金 鉛含量的測定 火焰原子吸收光譜法 | Aluminium and aluminium alloys; Determination of lead content; Flame atomic absorption spectrometric method |
| ISO 4193-1981 | 鋁和鋁合金 鉻含量的測定 火焰原子吸收光譜法 | Aluminium and aluminium alloys; Determination of chromium content; Flame atomic absorption spectrometric method |
| ISO 4280-1977 | 工業用天然及人造冰晶石和氟化鋁 硫酸鹽含量的測定 硫酸鋇重量法 | Cryolite, natural and artificial, and aluminium fluoride for industrial use; Determination of sulphate content; Barium sulphate gravimetric method |
| ISO 4295-1988 | 錳礦石和錳精礦 鋁含量的測定 光度法和重量法 | Manganese ores and concentrates; determination of aluminium content; photometric and gravimetric methods |
| ISO 4623-2 Technical Corrigendum 1-2005 | 色漆和清漆.耐絲狀腐蝕的測定.第2部分:鋁基質.技術勘誤1 | Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates; Technical Corrigendum 1 |
| ISO 4623-2-2003 | 色漆和清漆.耐絲狀腐蝕的測定.第2部分:鋁基質 | Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates |
| ISO 4688-1-2006 | 鐵礦石.鋁的測定.第1部分:火焰原子吸收光譜法 | Iron ores - Determination of aluminium - Part 1: Flame atomic absorption spectrometric method |
| ISO 5000-2005 | 商品級及拉伸級連續熱浸鍍鋁-硅冷軋?zhí)妓劁摫“? | Continuous hot-dip aluminium-silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities |
| ISO 5193-1981 | 加工鋁和鋁合金 拉制圓棒材 尺寸和形位(直徑采用對稱正負偏差)偏差 | Wrought aluminium and aluminium alloys; Drawn round bars; Tolerances on shape and dimensions (Symmetric plus and minus tolerances on diameter) |
| ISO 5194-1981 | 鋁和鋁合金 鋅含量的測定 火焰原子吸收光譜法 | Aluminium and aluminium alloys; Determination of zinc content; Flame atomic absorption spectrometric method |
| ISO 5832-11-1994 | 外科植入物.金屬材料.第11部分:鍛造鈦6鋁7鈮合金 | Implants for surgery - Metallic materials - Part 11: Wrought titanium 6-aluminium 7-niobium alloy |
| ISO 5832-14-2007 | 外科植入物.金屬材料.第14部分:鍛造鈦15-鉬5-鋯3-鋁合金 | Implants for surgery - Metallic materials - Part 14: Wrought titanium 15-molybdenum 5-zirconium 3-aluminium alloy |
| ISO 5832-3-1996 | 外科植入物.金屬材料.第3部分:鍛造鈦6鋁4釩合金 | Implants for surgery - Metallic materials - Part 3: Wrought titanium 6-aluminium 4-vanadium alloy |
| ISO 5889-1983 | 錳礦石和錳精礦 鋁、銅、鉛和鋅含量的測定 火焰原子吸收光譜法 | Manganese ores and concentrates; Determination of aluminium, copper, lead and zinc contents; Flame atomic absorption spectrometric method |
| ISO 5930-1979 | 工業用天然及人造冰晶石和氟化鋁 磷含量的測定 還原磷鉬酸鹽光度法 | Cryolite, natural and artificial, and aluminium fluoride for industrial use; Determination of phosphorus content; Reduced molybdophosphate photometric method |
| ISO 5931-2000 | 鋁生產用碳素材料 煅燒焦和煅燒碳產品 用艾氏卡法測定全硫含量 | Carbonaceous materials used in the production of aluminium - Calcined coke and calcined carbon products - Determination of total sulfur by the Eschka method |
| ISO 5938-1979 | 工業用天然及人造冰晶石和氟化鋁 硫含量的測定 X射線熒光光譜法 | Cryolite, natural and artificial, and aluminium fluoride for industrial use; Determination of sulphur content; X-ray fluorescence spectrometric method |
| ISO 5939-1980 | 鋁生產用碳素材料 電極用瀝青 水含量的測定 共沸蒸餾(Dean and Stark)法 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of water content; Azeotropic distillation (Dean and Stark) method |
| ISO 5940-1981 | 鋁生產用碳素材料 電極用瀝青 用環和球法測定軟化點 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of softening point by the ring-and-ball method |
| ISO 5940-2-2007 | 鋁生產用碳素材料.電極用瀝青.第2部分:軟化點的測定(梅特勒軟化點法) | Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Part 2: Determination of the softening point (Mettler softening point method) |
| ISO 6138-1991 | 鋁土礦石 成分不均勻性的試驗測定 | Aluminium ores; experimental determination of the heterogeneity of constitution |
| ISO 6139-1993 | 鋁土礦石 分配器的均勻分配的實驗室測定 | Aluminium ores; experimental determination of the heterogeneity of distribution of a lot |
| ISO 6140-1991 | 鋁土礦石 樣品的制備 | Aluminium ores; preparation of samples |
| ISO 6257-2002 | 鋁生產用碳素材料.電極用瀝青.取樣 | Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Sampling |
| ISO 6279-2006 | 滑動軸承.固體軸承用鋁合金 | Plain bearings - Aluminium alloys for solid bearings |
| ISO 6361-1-1986 | 加工鋁和鋁合金薄板、帶、厚板 第1部分:交貨和驗收的技術條件 | Wrought aluminium and aluminium alloy sheets, strips and plates; Part 1 : Technical conditions for inspection and delivery |
| ISO 6361-2-1990 | 加工鋁和鋁合金薄板、帶、厚板 第2部分:力學性能 | Wrought aluminium and aluminium alloy sheets, strips and plates; part 2: mechanical properties |
| ISO 6361-3-1985 | 加工鋁和鋁合金薄板、帶、厚板 第3部分:帶材 尺寸和形狀公差 | Wrought aluminium and aluminium alloy sheets, strips and plates; Part 3 : Strips; Tolerances on shape and dimensions (Previously referenced DIS 8219) |
| ISO 6361-4-1988 | 加工鋁和鋁合金薄板、帶、厚板 第4部分:薄板和厚板 尺寸和形狀公差 | Wrought aluminium and aluminium alloy sheets, strips and plates; part 4: sheets and plates; tolerances on shape and dimensions |
| ISO 6362-1-1986 | 加工鋁和鋁合金擠壓棒/條材、管材和型材 第1部分:驗收和交貨的技術條件 | Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles; Part 1 : Technical conditions for inspection and delivery |
| ISO 6362-2-1990 | 加工鋁和鋁合金擠壓棒/條材、管材和型材 第2部分:力學性能 | Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles; part 2: mechanical properties |
| ISO 6362-3-2001 | 加工鋁和鋁合金擠壓棒/條材、管材和型材 第3部分：擠壓矩形棒材 形狀和尺寸公差 | Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles - Part 3: Extruded rectangular bars; Tolerances on shape and dimensions |
| ISO 6362-4-1988 | 加工鋁和鋁合金擠壓棒/條材、管材和型材 第4部分:擠壓型材 尺寸和形狀公差 | Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles; part 4: extruded profiles; tolerances on shape and dimensions |
| ISO 6362-5-2001 | 加工鋁和鋁合金擠壓棒/條材、管材和型材 第5部分:擠壓圓形、正方形和六角形棒材 尺寸和形狀公差 | Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles - Part 5: Extruded round, square and hexagonal bars; Tolerances on shape and dimensions |
| ISO 6363-1-1988 | 加工鋁和鋁合金冷拉棒/條材和管材 第1部分:驗收及交貨的技術條件 | Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes; part 1: technical conditions for inspection and delivery |
| ISO 6363-2-1993 | 加工鋁和鋁合金冷拉棒/條材和管材 第2部分:力學性能 | Wrought aluminium and aluminium alloy; cold-drawn rods/bars and tubes; part 2: mechanical properties |
| ISO 6363-4-1991 | 加工鋁和鋁合金冷拉棒/條材和管材 第4部分:拉制矩形棒材 尺寸和形狀公差 | Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes; part 4: drawn rectangular bars; tolerances on form and dimensions |
| ISO 6363-5-1992 | 加工鋁和鋁合金冷拉棒/條材和管材 第5部分:冷拉方形和六角形棒材 尺寸和形狀公差 | Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes; part 5: drawn square and hexagonal bars; tolerances on form and dimensions |
| ISO 6365-1-1988 | 加工鋁和鋁合金冷拉線材 第1部分:驗收及交貨的技術條件 | Wrought aluminium and aluminium alloy cold-drawn wire; part 1: technical conditions for inspection and delivery |
| ISO 6374-1981 | 工業用天然及人造冰晶石和氟化鋁 磷含量的測定 萃取后原子吸收光譜法 | Cryolite, natural and artificial, and aluminium fluoride for industrial use; Determination of phosphorus content; Atomic absorption spectrometric method after extraction |
| ISO 6375-1980 | 鋁生產用碳素材料 電極用焦 取樣 | Carbonaceous materials for the production of aluminium; Cokes for electrodes; Sampling |
| ISO 6376-1980 | 鋁生產用碳素材料 電極用瀝青 甲苯不溶物含量的測定 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of content of toluene-insoluble material |
| ISO 6474-1994 | 外科植入物.高純氧化鋁陶瓷材料 | Implants for surgery; ceramic materials based on high purity alumina |
| ISO 6581-1980 | 鋁和鋁合金的陽極氧化 著色陽極氧化膜耐紫外光的測定 | Anodizing of aluminium and its alloys; Determination of the fastness to ultra-violet light of coloured anodic oxide coatings |
| ISO 6606-1986 | 鋁土礦石 在1075℃下質量損失的測定 重量法 | Aluminium ores; Determination of loss of mass at 1 075 degrees C; Gravimetric method |
| ISO 6607-1985 | 鋁土礦石 總硅含量的測定 重量和分光光度聯合法 | Aluminium ores; Determination of total silicon content; Combined gravimetric and spectrophotometric method |
| ISO 6609-1985 | 鋁土礦石 鐵含量的測定 滴定法 | Aluminium ores; Determination of iron content; Titrimetric method |
| ISO 6719-1986 | 陽極氧化鋁和鋁合金 用積分球儀法測量鋁表面的反射特性 | Anodized aluminium and aluminium alloys; Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments |
| ISO 6791-1981 | 鋁生產用碳素材料 電極用瀝青 喹啉不溶物含量的測定 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of contents of quinoline-insoluble material |
| ISO 6827-1981 | 鋁和鋁合金 鈦含量的測定 二安替吡啉甲烷光度法 | Aluminium and aluminium alloys; Determination of titanium content; Diantipyrylmethane photometric method |
| ISO 6830-1986 | 鐵礦石 鋁含量的測定 EDTA滴定法 | Iron ores; Determination of aluminium content; EDTA titrimetric method |
| ISO 6994-1986 | 鋁土礦石 鋁含量的測定 EDTA滴定法 | Aluminium ores; Determination of aluminium content; EDTA titrimetric method |
| ISO 6995-1985 | 鋁土礦石 鈦含量的測定 4,4'-二安替吡啉甲烷分光光度法 | Aluminium ores; Determination of titanium content; 4,4'-Diantipyrylmethane spectrophotometric method |
| ISO 6997-1985 | 鋁生產用碳素材料 煅燒焦 表觀油含量的測定 加熱法 | Carbonaceous materials for the production of aluminium; Calcined coke; Determination of apparent oil content ; Heating method |
| ISO 6998 Technical Corrigendum 1-1999 | 鋁生產用碳素材料 電極用瀝青 焦化值的測定 技術勘誤1 | Carbonaceous materials for the production of aluminium - Pitch for electrodes - Determination of coking value; Technical Corrigendum 1 |
| ISO 6998-1997 | 鋁生產用碳素材料 電極用瀝青 焦化值的測定 | Carbonaceous materials for the production of aluminium - Pitch for electrodes - Determination of coking value |
| ISO 6999-1983 | 鋁生產用碳素材料 電極用瀝青 密度的測定 比重瓶法 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of density; Pycnometric method |
| ISO 7061-1993 | 造船 海船用鋁質舷梯 | Shipbuilding; aluminium shore gangways for seagoing vessels |
| ISO 7271-1982 | 鋁和鋁合金 箔材和薄帶材 尺寸公差 | Aluminium and aluminium alloys; Foil and thin strip; Dimensional tolerances |
| ISO 7273-1981 | 鍛鋁和鋁合金.擠壓圓型材.形狀和尺寸公差 | Wrought aluminium and aluminium alloys; Extruded round bars; Tolerances on shape and dimensions |
| ISO 7274-1981 | 加工鋁和鋁合金 冷拉圓棒材 尺寸和形狀公差(直徑采用負公差) | Wrought aluminium and aluminium alloys - Drawn round bars - Tolerances on shape and dimensions (All minus tolerances on diameter) |
| ISO 7530-7-1992 | 鎳合金 火焰原子吸收光譜法 第7部分:鋁含量測定 | Nickel alloys; flame atomic absorption spectrometric analysis; part 7: determination of aluminium content |
| ISO 7583-1986 | 鋁和鋁合金的陽極氧化 術語 三種語言版 | Anodizing of aluminium and its alloys; Vocabulary Trilingual edition |
| ISO 7599-1983 | 鋁和鋁合金的陽極氧化 鋁的陽極氧化膜一般規范 | Anodizing of aluminium and its alloys; General specifications for anodic oxide coatings on aluminium |
| ISO 7668-1986 | 陽極氧化鋁和鋁合金.20°、45°、60°或85°角的鏡面反射率和鏡面光澤的測量 | Anodized aluminium and aluminium alloys; measurement of specular reflectance and specular gloss at angles of 20°, 45°, 60° or 85° |
| ISO 7722-1985 | 重力鑄造、砂型鑄造、冷硬鑄造或由有關工藝生產的鋁合金鑄件 驗收和交貨的一般條件 | Aluminium alloy castings produced by gravity, sand, or chill casting, or by related processes; General conditions for inspection and delivery |
| ISO 7759-1983 | 鋁和鋁合金的陽極氧化 用遮光角度儀或角度儀測量鋁表面的反射特性 | Anodizing of aluminium and its alloys; Measurement of reflectivity characteristics of aluminium surfaces using abridged goniophotometer or goniophotometer |
| ISO 7866-1999 | 氣瓶 可重復充裝的鋁合金無縫氣瓶 設計、結構和試驗 | Gas cylinders - Refillable seamless aluminium alloy gas cylinders - Design, construction and testing |
| ISO 791-1973 | 鎂合金 鋁含量的測定 8-羥基喹啉重量法 | Magnesium alloys; Determination of aluminium; 8-hydroxyquinoline gravimetric method |
| ISO 793-1973 | 鋁和鋁合金 鐵含量的測定 鄰菲啰啉光度法 | Aluminium and aluminium alloys; Determination of iron; Orthophenanthroline photometric method |
| ISO 795-1976 | 鋁和鋁合金 銅含量的測定 草酰二酰肼光度法 | Aluminium and aluminium alloys; Determination of copper content; Oxalyldihydrazide photometric method |
| ISO 796-1973 | 鋁合金 銅含量的測定 電解法 | Aluminium alloys; Determination of copper; Electrolytic method |
| ISO 797-1973 | 鋁和鋁合金 硅含量的測定 重量法 | Aluminium and aluminium alloys; Determination of silicon; Gravimetric method |
| ISO 8003-1985 | 鋁生產用碳素材料 電極用瀝青 動態粘度的測定 | Carbonaceous materials used in the production of aluminium; Pitch for electrodes; Measurement of dynamic viscosity |
| ISO 8004-1985 | 鋁生產用碳素材料 煅燒焦和煅燒碳產品 二甲苯密度的測定 比重瓶法 | Carbonaceous materials for the production of aluminium; Calcined coke and calcined carbon products; Determination of the density in xylene; Pyknometric method |
| ISO 8005-2005 | 鋁生產用碳素材料.生焦炭和煅燒焦炭.灰分含量的測定 | Carbonaceous materials used in the production of aluminium - Green and calcined coke - Determination of ash content |
| ISO 8006-1985 | 鋁生產用碳素材料 電極用瀝青 灰分的測定 | Carbonaceous materials used in the production of aluminium; Pitch for electrodes; Determination of ash |
| ISO 8007-1-1999 | 鋁生產用碳素材料 單個材料的取樣方案和取樣 第1部分:陰極塊 | Carbonaceous materials used in the production of aluminium - Sampling plans and sampling from individual units - Part 1: Cathode blocks |
| ISO 8007-2-1999 | 鋁生產用碳素材料 單個材料的取樣方案和取樣 第2部分:預焙陽極 | Carbonaceous materials used in the production of aluminium - Sampling plans and sampling from individual units - Part 2: Prebaked anodes |
| ISO 8007-3-2003 | 鋁生產用碳素材料.單個材料的取樣方案和取樣.第3部分:側墻磚 | Carbonaceous materials used in the production of aluminium - Sampling plans and sampling from individual units - Part 3: Sidewall blocks |
| ISO 8008-2005 | 主要用于鋁生產的氧化鋁.吸附氮的比表面面積的測定 | Aluminium oxide primarily used for the production of aluminium -- Determination of specific surface area by nitrogen adsorption |
| ISO 802-1976 | 主要用于鋁生產的氧化鋁 試樣的制備和貯存 | Aluminium oxide primarily used for the production of aluminium; Preparation and storage of test samples |
| ISO 804-1976 | 主要用于鋁生產的氧化鋁 分析用溶液的制備 堿熔化法 | Aluminium oxide primarily used for the production of aluminium; Preparation of solution for analysis; Method by alkaline fusion |
| ISO 805-1976 | 主要用于鋁生產的氧化鋁 鐵含量的測定 1,10-菲羅啉光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of iron content; 1,10- Phenanthroline photometric method |
| ISO 8056-1-1985 | 航空器 鎳鉻和鎳鋁熱電偶的延伸電纜 第1部分:導線 一般要求和試驗 | Aircraft; Nickel-chromium and nickel-aluminium thermocouple extension cables; Part 1 : Conductors; General requirements and tests |
| ISO 8056-2-1988 | 航空器 鎳鉻和鎳鋁熱電偶的延伸電纜 第2部分:端頭 一般要求和試驗 | Aircraft; nickel-chromium and nickel-aluminium thermocouple extension cables; part 2: terminations; general requirements and tests |
| ISO 8056-3-1987 | 航空器 鎳鉻和鎳鋁熱電偶的延伸電纜 第3部分:壓接式環形端子 尺寸 | Aircraft; Nickel-chromium and nickel-aluminium thermocouple extension cables; Part 3 : Crimp-type ring terminal ends; Dimensions |
| ISO 8056-4-1987 | 航空器 鎳鉻和鎳鋁熱電偶的延伸電纜 第4部分:壓接式對接接頭 尺寸 | Aircraft; Nickel-chromium and nickel-aluminium thermocouple extension cables; Part 4 : Crimp-type butt connectors; Dimensions |
| ISO 806-2004 | 主要用于鋁生產的氧化鋁.在300℃和1000℃時質量損失的測定 | Aluminium oxide primarily used for the production of aluminium - Determination of loss of mass at 300 °C and 1000 °C |
| ISO 8078-1984 | 航空航天工藝 鋁合金的陽極化處理 無著色涂層的硫酸工藝規程 | Aerospace process; Anodic treatment of aluminium alloys; Sulfuric acid process, undyed coating |
| ISO 8079-1984 | 航空航天工藝 鋁合金的陽極化處理 帶著色涂層的硫酸工藝規程 | Aerospace process; Anodic treatment of aluminium alloys; Sulfuric acid process, dyed coating |
| ISO 808-1973 | 鋁和鋁合金 硅含量的測定 鉬藍分光光度法 | Aluminium and aluminium alloys; Determination of silicon; Spectrophotometric method with the reduced silicomolybdic complex |
| ISO 8081-1985 | 航空航天工藝 鋁合金的化學轉化涂鍍 一般用途 | Aerospace process; Chemical conversion coating for aluminium alloys; General purpose |
| ISO 8220-1986 | 主要用于鋁生產的氧化鋁 微晶粒(小于60毫微米篩目)大小分布的測定 電沉積篩分法 | Aluminium oxide primarily used for the production of aluminium; Determination of the fine particle size distribution (less than 60 mu/m); Method using electroformed sieves |
| ISO 8251-1987 | 陽極氧化鋁和鋁合金 用摩擦輪磨耗試驗機測定陽極氧化膜磨性和耐磨系數 | Anodized aluminium and aluminium alloys; Measurement of wear resistance and wear index of anodic oxidation coatings with an abrasive wheel wear test apparatus |
| ISO 8252-1987 | 陽極氧化鋁和鋁合金 用噴砂摩擦試驗儀測定陽極氧化膜的平均耐磨系數 | Anodized aluminium and aluminium alloys; Measurement of mean specific abrasion resistance of anodic oxidation coatings with an abrasive jet test apparatus |
| ISO 8362-3-2001 | 注射容器及附件 第3部分：注射瓶鋁蓋 | Injection containers and accessories - Part 3: Aluminium caps for injection vials |
| ISO 8362-6-1992 | 注射劑用注射容器及附件 第6部分:鋁塑組合注射瓶蓋 | Injection containers for injectables and accessories; part 6: caps made of aluminium-plastics combinations for injection vials |
| ISO 8362-7-2006 | 注射容器及附件.第7部分:無凸緣鋁塑組合注射瓶蓋 | Injection containers and accessories - Part 7: Injection caps made of aluminium-plastics combinations without overlapping plastics part |
| ISO 8536-3-1999 | 醫用輸液器具 第3部分:輸液瓶鋁蓋 | Infusion equipment for medical use - Part 3: Aluminium caps for infusion bottles |
| ISO 8536-7-2009 | 醫用輸液設備.第7部分:輸液瓶用鋁和塑料復合物制帽蓋 | Infusion equipment for medical use - Part 7: Caps made of aluminium-plastics combinations for infusion bottles |
| ISO 8556-1986 | 鋁土礦石 磷含量的測定 鉬藍分光光度測定法 | Aluminium ores; Determination of phosphorus content; Molybdenum blue spectrophotometric method |
| ISO 8557-1985 | 鋁土礦石 分析試樣中濕存水的測定 重量法 | Aluminium ores; Determination of hygroscopic moisture in analytical samples; Gravimetric method |
| ISO 8558-1985 | 鋁土礦石 預干燥試樣的制備 | Aluminiumn ores; Preparation of pre-dried test samples |
| ISO 8591-1-1989 | 航空航天 鍛鋁和鋁合金 檢驗、試驗和供貨要求 第1部分:一般要求 | Aerospace; wrought aluminium and aluminium alloys; inspection, testing and supply requirements; part 1: general requirements |
| ISO 8658-1997 | 鋁生產用碳素材料 未煅燒和煅燒焦 火焰原子吸收光譜法測定痕量元素 | Carbonaceous materials for use in the production of aluminium - Green and calcined coke - Determination of trace elements by flame atomic absorption spectroscopy |
| ISO 8685-1992 | 鋁土礦石 取樣方法 | Aluminium ores; sampling procedures |
| ISO 8723-1986 | 鋁生產用碳素材料 煅燒焦 油含量的測定 溶劑萃取法 | Carbonaceous materials for the production of aluminium; Calcined coke; Determination of oil content; Method by solvent extraction |
| ISO 886-1973 | 鋁和鋁合金 錳含量的測定 光度法(錳含量為0.005～1.5%) | Aluminium and aluminium alloys; Determination of manganese; Photometric method (Manganese content between 0,005 and 1,5 %) |
| ISO 8872-2003 | 輸血、輸液和注射瓶鋁蓋－一般要求和試驗方法 | Aluminium caps for transfusion, infusion and injection bottles - General requirements and test methods |
| ISO 8889-1988 | 鉻礦石和鉻精礦 鋁含量的測量 絡合法 | Chromium ores and concentrates; determination of aluminium content; complexometric method |
| ISO 8993-1989 | 陽極氧化鋁和鋁合金 點腐蝕法評定鋁及鋁合金陽極氧化膜 圖表法 | Anodized aluminium and aluminium alloys; rating system for the evaluation of pitting corrosion; chart method |
| ISO 8994-1989 | 陽極氧化鋁和鋁合金 點腐蝕法評定鋁及鋁合金陽極氧化膜 網格法 | Anodized aluminium and aluminium alloys; rating system for the evaluation of pitting corrosion; grid method |
| ISO 900-1977 | 主要用于鋁生產的氧化鋁 鈦含量的測定 二安替吡啉基代甲烷光度法 | Aluminium oxide primarily used for the production of aluminium; Determination of titanium content; Diantipyrylmethane photometric method |
| ISO 901-1976 | 主要用于鋁生產的氧化鋁 絕對密度的測定 比重瓶法 | Aluminium oxide primarily used for the production of aluminium; Determination of absolute density; Pyknometer method |
| ISO 902-1976 | 主要用于鋁生產的氧化鋁 休止角的測定 | Aluminium oxide primarily used for the production of aluminium; Measurement of the angle of repose |
| ISO 903-1976 | 主要用于鋁生產的氧化鋁 未夯實密度的測定 | Aluminium oxide primarily used for the production of aluminium; Determination of untamped density |
| ISO 9033-1989 | 鋁土礦石 散裝料水含量的測定 | Aluminium ores; determination of the moisture content of bulk material |
| ISO 9055-1988 | 鋁生產用碳素材料 電極用瀝青 用氧彈法測定硫含量 | Carbonaceous materials for the production of aluminium; pitch for electrodes; determination of sulfur content by the bomb method |
| ISO 9088-1997 | 鋁生產用碳素材料 預焙陽極和陰極塊 用比重瓶法測定二甲苯密度 | Carbonaceous materials used for the production of aluminium - Cathode blocks an prebacked anodes - Determination of the density in xylene by a pyknometric method |
| ISO 9208-1989 | 鋁土礦石 釩含量的測定 苯甲酰苯基羥胺(BPHA)分光光度法 | Aluminium ores; determination of vanadium content; BPHA spectrophotometric method |
| ISO 9285-1997 | 磨料粒度 電熔氧化鋁的化學分析 | Abrasive grains and crude - Chemical analysis of fused aluminium oxide |
| ISO 9364-2006 | 商品級、拉制成型級和結構級連續熱鍍鋁/鋅薄鋼板質量 | Continuous hot-dip aluminium/zinc-coated steel sheet of commercial, drawing and structural qualities |
| ISO 9406-1995 | 鋁生產用碳素材料 焦碳 用重量分析法測定揮發物的含量 | Carbonaceous materials for the production of aluminium - Green coke - Determination of volatile matter content by gravimetric analysis |
| ISO 9418-1998 | 航空航天 鋁或鋁合金實心鉚釘 采購規范 | Aerospace - Rivets, solid, in aluminium or aluminium alloys - Procurement specification |
| ISO 9591-2004 | 鋁合金的腐蝕.抗應力腐蝕裂紋的測定 | Corrosion of aluminium alloys - Determination of resistance to stress corrosion cracking |
| ISO 9606-2-2004 | 焊工的認可試驗.熔焊.第2部分:鋁和鋁合金 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys |
| ISO 9658-1990 | 鋼 鋁含量的測定 火焰原子吸收光譜法 | Steel; determination of aluminium content; flame atomic absorption spectrometric method |
| ISO 9692-3-2000 | 焊接和相關工藝 接頭制備的建議 第3部分:鋁及鋁合金的金屬焊條惰性氣體保護焊和鎢焊條惰性氣體保護焊 | Welding and allied processes - Recommendations for joint preparation - Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| ISO 9915-1992 | 鋁合金鑄件 X射線照相試驗 | Aluminium alloy castings; radiography testing |
| ISO 9916-1991 | 鋁合金和鎂合金鑄件 液體滲透檢驗 | Aluminium alloy and magnesium alloy castings; liquid penetrant inspection |
| ISO/TR 11069 Technical Corrigendum 1-1996 | 鋁結構 材料和設計 靜態負荷下的極限狀態 技術勘誤1 | Aluminium structures - Material and design - Ultimate limit state under static loading; Technical Corrigendum 1 |
| ISO/TR 11069-1995 | 鋁結構 材料和設計 靜態負荷下的極限狀態 | Aluminium structures - Material and design - Ultimate limit state under static loading |
| ISO/TR 11728-1993 | 陽極氧化鋁和鋁合金 使用循環的人工燈和污染空氣測定著色陽極氧化膜色牢度的加速耐候試驗 | Anodized aluminium and aluminium alloys; accelerated test of weather fastness of coloured anodic oxide coatings using cyclic artificial light and pollution gas |
| ISO/TR 17671-4-2002 | 焊接.金屬材料焊接的推薦.第4部分:鋁和鋁合金的電弧焊接 | Welding - Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys |
| ISO/TR 22694-2008 | 氣瓶.定期檢驗和測試時無縫鋼和鋁合金氣瓶的裂紋用認可/拒絕的確定方法 | Gas cylinders - Methods for establishing acceptance/rejection criteria for flaws in seamless steel and aluminium alloy cylinders at time of periodic inspection and testing |
| ISO/TR 7242-1981 | 輕金屬和鋁合金的化學分析 實驗室間的試驗結果的統計分析 | Chemical analysis of light metals and their alloys; Statistical interpretation of inter-laboratory trials |
| ISO/TR 8125-1984 | 鋁和鋁合金的陽極氧化 著色陽極氧化膜的顏色和色差的測定 | Anodizing of aluminium and its alloys; Determination of colour and colour difference of coloured anodic coatings |
| ISO/TS 14423-1999 | 鋁生產用碳素材料 冷壓糊 通過喹啉萃取和測定聚焦體尺寸分布來測定有效粘接劑含量和聚焦體含量 | Carbonaceous materials used in the production of aluminium - Cold-ramming pastes - Determination of effective binder content and aggregate content by extraction with quinoline, and determination of aggregate size distribution |
| ISO/TS 14425-1999 | 鋁生產用碳素材料 冷壓糊 未焙燒糊料的揮發物含量的測定 | Carbonaceous materials used in the production of aluminium - Cold-ramming pastes - Determination of volatile-matter content of unbaked pastes |
| 編號 | 中文名稱 | 英文名稱 |