| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| CR 1404-1994 | 型式試驗時氣體燃料器具的排放的測定 | Determination of emissions from appliances burning gaseous fuels during type-testing |
| CR 1472-1997 | 關于氣體用具標識的通用指南 | General guidance for the marking of gas appliances |
| CR 1749-2001 | 歐洲依照產品燃燒（各類）排空法的氣體燃具分類體系 | European scheme for the classification of gas appliances according to the method of evacuation of the products of combustion (types) |
| EN 10276-2-2003 | 鋼鐵材料的化學分析 鋼和鐵中氧的測定 第2部分：在惰性氣體條件下熔融后用紅外光譜法測定 | Chemical analysis of ferrous materials - Determination of oxygen content in steel and iron - Part 2: Infrared method after fusion under inert gas |
| EN 10301-2003 | 岸上和海上管路鋼管及配件 減小非腐蝕性氣體輸送摩擦力的內涂層 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas |
| EN 1057-1996 | 銅和銅合金 在衛生和加熱器中輸送水和氣體用無縫圓銅管 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 1074-4-2000 | 供水閥門 目的要求的適應性和合適的認證試驗 第4部分：氣體閥門 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 4: Air valves |
| EN 1076-1997+AC-1997 | 工場環境 測定氣體和蒸氣用的泵吸附管 要求和試驗方法 | Workplace atmospheres - Pumped sorbent tubes for the determination of gases and vapours - Requirements and test methods |
| EN 1084-1995 | 膠合板 用氣體分析法測定甲醛釋放級別 | Plywood - Formaldehyde release classes determined by the gas analysis method |
| EN 1106-2001 | 氣體燃燒器具用人工操作絲錐 | Manually operated taps for gas burning appliances |
| EN 1127-1-1997 | 爆炸性氣體 爆炸防止和防護 第1部分：.基本概念和方法 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| EN 1127-2-2002 | 爆炸性氣體 爆炸防止和防護 第2部分：.采礦的基本概念和方法 | Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining |
| EN 12022-1999 | 血液氣體交換器 | Blood gas exchangers |
| EN 12071-1999 | 焊接易耗品 耐蠕變鋼的氣體遮蔽金屬電弧焊用管狀焊條 分級 | Welding consumables - Tubular cored electrodes for gas shielded metal arc welding of creep-resisting steels - Classification |
| EN 12073-1999 | 焊接易耗品 不銹鋼和耐熱鋼有或無氣體遮蔽金屬電弧焊接用管狀有芯焊條 分級 | Welding consumables - Tubular cored electrodes for metal arc welding with or without a gas shield of stainless and heat-resisting steels - Classification |
| EN 12083-1998+AC-2000 | 呼吸保護裝置 帶呼吸軟管的過濾器（無面罩式過濾器） 微粒過濾器、氣體過濾器和混合式過濾器 要求、試驗 | Respiratory protective devices - Filters with breathing hoses (Non-mask mounted filters) - Particle filters, gas filters, and combined filters - Requirements, testing, marking |
| EN 12094-1-2003 | 固定式消防系統 氣體滅火系統的部件 第1部分：對電自動控制和延遲裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices |
| EN 12094-10-2003 | 固定式消防系統 氣體滅火系統的部件 第10部分：對壓力計壓力開關的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 10: Requirements and test methods for pressure gauges and pressure switches |
| EN 12094-11-2003 | 固定式消防系統 氣體滅火系統的部件 第11部分：機械稱重裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 11: Requirements and test methods for mechanical weighing devices |
| EN 12094-12-2003 | 固定式消防系統 氣體滅火系統的部件 第12部分：氣體報警裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 12: Requirements and test methods for pneumatic alarm devices |
| EN 12094-13-2001+AC-2002 | 固定式消防系統 氣體滅火系統的部件 第13部分：對止回閥和非回流閥的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 13: Requirements and test methods for check valves and non-return valves |
| EN 12094-16-2003 | 固定式消防系統 氣體滅火系統的部件 第16部分：對CO2低壓系統的氣味測定裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 16: Requirements and test methods for odorizing devices for CO<(Index)2> low pressure systems |
| EN 12094-2-2003 | 固定式消防系統 氣體滅火系統的部件 第2部分：對非電自動控制和延遲裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 2: Requirements and test methods for non-electric automatic control and delay devices |
| EN 12094-3-2003 | 固定式消防系統 氣體滅火系統的部件 第3部分：對手動觸發和停止裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 3: Requirements and test methods for manual triggering and stop devices |
| EN 12094-5-2000 | 固定式消防系統 氣體滅火系統的部件 第5部分：高、低壓選擇閥及其CO2系統驅動器觸發要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 5: Requirements and test methods for high and low pressure selector valves and their actuators for CO<(Index)2> systems |
| EN 12094-6-2000 | 固定式消防系統 氣體滅火系統的部件 第6部分：對CO2系統的非電阻塞裝置的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 6: Requirements and test methods for non-electrical disable devices for CO<(Index)2> systems |
| EN 12094-7-2000 | 固定式消防系統 氣體滅火系統的部件 第7部分：對CO2系統的噴嘴的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 7: Requirements and test methods for nozzles for CO<(Index)2> systems |
| EN 12094-8-1998 | 固定式消防系統 氣體滅火系統的部件 第8部分：二氧化碳設備用撓性連接器的要求及試驗方法 | Fixed fire fighting systems - Components for gas extinguishing systems - Part 8: Requirements and test methods for flexible connectors for CO<(Index)2> systems |
| EN 12094-9-2003 | 固定式消防系統 氣體滅火系統的部件 第9部分：對專用火焰探測器的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 9: Requirements and test methods for special fire detectors |
| EN 12115-1999 | 液體或氣體化學藥品用的橡膠和熱塑軟管和軟管組件 規范 | Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification |
| EN 12405-2002 | 氣量計 氣體體積電子轉換裝置 | Gas meters - Gas-volume electronic conversion devices |
| EN 12534-1999 | 焊接消耗品 高強度鋼氣體保護金屬電弧焊用絲狀電極、焊絲和焊條和沉漬物 分類 | Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded metal arc welding of high strength steels - Classification |
| EN 12535-2000 | 焊接消耗品 高強度鋼氣體保護金屬電弧焊用管型藥芯焊條 分類 | Welding consumables - Tubular cored electrodes for gas shielded metal arc welding of high strength steels - Classification |
| EN 12561-3-2002 | 鐵路用 油罐車 第3部分：加壓液化氣體用罐底加注和排空裝置 | Railway applications - Tank wagons - Part 3: Bottom filling and emptying devices for gases liquified under pressure |
| EN 1266-2002 | 為使助燃空氣和燃料氣體或加速傳輸裝入風扇的獨立對流燃燒火焰加熱器 | Independent gas-fired convection heaters incorporating a fan to assist transportation of combustion air and/or flue gases |
| EN 1279-3-2002 | 建筑玻璃 隔離玻璃裝置 第3部分：漏氣率和氣體濃度容差的長期試驗方法和要求 | Glass in building - Insulating glass units - Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances |
| EN 13014-2000 | 與麻醉和呼吸設備相連的氣體采樣管連接器 | Connections for gas sampling tubes to anaesthetic and respiratory equipment |
| EN 13090-2000 | 建筑物中氣體管道螺紋接頭再密封方法 | Means for resealing threaded joints of gas pipework in buildings |
| EN 13185-2001 | 無損檢測 密封試驗 示蹤氣體法 | Non-destructive testing - Leak testing - Tracer gas method |
| EN 13192-2001 | 無損檢測 密封試驗 氣體標準漏出物校準 | Non destructive testing - Leak testing - Calibration of reference leaks for gases |
| EN 13220-1998 | 與醫用氣體管道系統的終端設備相連的流量計 | Flow-metering devices for connection to terminal units of medical gas pipeline systems |
| EN 13221-2000 | 醫用氣體用高壓撓性連接 | High pressure flexible connections for use with medical gases |
| EN 1326-1996 | 氣焊設備 氣體釬焊和定位焊接用小型設備 | Gas welding equipment - Small kits for gas brazing and welding |
| EN 13348-2001 | 銅和銅合金 醫用氣體或真空用無縫圓銅管 | Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum |
| EN 13528-1-2002 | 環境空氣質量 測定氣體和蒸氣濃度的擴散取樣器 要求和試驗方法 第1部分：一般要求 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours; Requirements and test methods - Part 1: General requirements |
| EN 13528-2-2002 | 環境空氣質量 測定氣體和蒸氣濃度的擴散取樣器 要求和試驗方法 第2部分：特殊要求和試驗方法 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours; Requirements and test methods - Part 2: Specific requirements and test methods |
| EN 13625-2001 | 無損檢測 檢漏 測量氣體泄漏的儀器的選擇指南 | Non-destructive testing - Leak test - Guide to the selection of instrumentation for the measurement of gas leakage |
| EN 13673-1-2003 | 最大爆炸壓力及氣體和蒸汽壓力最大上升速度的測定 第1部分：最大爆炸壓力的測定 | Determination of the maximum explosion pressure and the maximum rate of pressure rise of gases and vapours - Part 1: Determination of the maximum explosion pressure |
| EN 13774-2003 | 最大工作壓力小于或等于16 bar的氣體分配系統用閥門 性能要求 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements |
| EN 14031-2003 | 工作環境 空氣中有毒氣體的測定 | Workplace atmospheres - Determination of airborne endotoxin |
| EN 14091-2002 | 航天產品質量保證 航天材料篩屑的熱真空氣體釋放試驗 | Space product assurance - Thermal vacuum outgassing test for the screening of space materials |
| EN 141-2000 | 呼吸保護裝置 氣體過濾器和組合過濾器 要求、測試、標志 | Respiratory protective devices - Gas filters and combined filters - Requirements, testing, marking |
| EN 14100-2001 | 航天產品質量保證 用于有人駕駛的航天宇航艙廢的材料和裝配器件的釋放氣體的測定 | Space product assurance - The determination of offgassing products from materials and assembled articles to be used in a manned space vehicle crew compartment |
| EN 14382-2002 | 氣壓調節站的安全設備和安裝 入口壓力達100bar的氣體安全關閉裝置 | Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar |
| EN 144-3-2003 | 呼吸保護裝置 氣瓶閥 第3部分：潛水氣體硝基氧和氧氣的出口連接 | Respiratory protective devices - Gas cylinder valves - Part 3: Outlet connections for diving gases Nitrox and oxygen |
| EN 1555-1-2002 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第1部分：總則 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-2-2002 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第2部分：管材 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| EN 1555-3-2002 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第3部分：管件 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1555-4-2002 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第4部分：閥門 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1555-5-2002 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第5部分：針對系統用途的適合性 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 161-2001 | 氣體燃燒器和燃氣器具自動關閉閥 | Automatic shut-off valves for gas burners and gas appliances |
| EN 1643-2000 | 氣體燃燒器和氣體設備自動關閉閥門的閥門檢驗系統 | Valve proving systems for automatic shut-off valves for gas burners and gas appliances |
| EN 1668-1997 | 焊接耗材 非合金和細晶粒鋼的惰性氣體保護鎢極焊用焊條 焊絲和熔敷 分類 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non alloy and fine grain steels - Classification |
| EN 1755-2000 | 工業用卡車的安全 潛在爆炸環境下的操作 在可燃氣體、蒸氣、 潮濕和灰塵中使用 | Safety of industrial trucks - Operation in potentially explosive atmospheres - Use in flammable gas, vapour, mist and dust |
| EN 1775-1998+A1-2000+A2-2000 | 供氣 建筑物中的氣體管道工程 最大運轉壓力≤5巴功能推薦 | Gas supply - Gas pipework for buildings - Maximum operating pressure 5 bar - Functional recommendations |
| EN 1797-2001 | 低溫容器 氣體/材料兼容性 | Cryogenic vessels - Gas/material compatibility |
| EN 1827-1999 | 呼吸保護裝置 防止氣體或氣體和微粒或僅防顆粒的無吸入閥和帶可分離過濾器的半掩面罩 要求、試驗和標記 | Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only - Requirements, testing, marking |
| EN 1834-1-2000 | 往復式內燃發動機 用在潛在爆炸環境下發動機設計結構和安全要求 第1部分：用在可燃氣體和蒸氣環境的II組 | Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Part 1: Group II engines for use in flammable gas and vapour atmospheres |
| EN 1839-2003 | 氣體和蒸氣爆炸限值的測定 | Determination of explosion limits of gases und vapours |
| EN 1854-1997+A1-1998 | 氣體燃燒器和氣體燃燒器具的壓敏器件 | Pressure sensing devices for gas burners and gas burning appliances |
| EN 1911-1-1998 | 固定源輻射 HCI的人工測定法 第1部分：氣體的抽樣 | Stationary source emissions - Manual method of determination of HCl - Part 1: Sampling of gases |
| EN 1911-2-1998 | 固定源輻射 HCI的人工測定法 第2部分：氣體混合物吸收 | Stationary source emissions - Manual method of determination of HCl - Part 2: Gaseous compounds absorption |
| EN 1975/prA1-2003 | 可運輸氣瓶 容積從0.5L至150L可再灌裝可運輸無縫鋁和鋁合金氣體瓶設計和結構規范 修改A1 | Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litres; Amendment A1 / Note: Intended as an amendment to EN |
| EN 203-1-1992+A1-1995+A2-1999 | 氣體加熱供膳設備 第1部分：安全要求 | Gas heated catering equipment; part 1: safety requirements |
| EN 203-2-1995 | 氣體加熱供膳設備 第2部分：能源的合理使用 | Gas heated catering equipment - Part 2: Rational use of energy |
| EN 26184-2-1991 | 抑爆系統 第2部分：空氣中易燃氣體爆炸指數的測定 | Explosion protection systems; part 2 : determination of explosion indices of combustible gases in air (ISO 6184-2:1985) |
| EN 26184-3-1991 | 抑爆系統 第3部分：除粉塵/空氣和氣體/空氣混合物以外的燃料/空氣混合物爆炸指數的測定 | Explosion protection systems; Part 3 : Determination of explosion indices of fuel/air mixtures other than dust/air and gas/air mixtures (ISO 6184-3:1985) |
| EN 26848-1991 | 惰性氣體保護電弧焊接以及等離子氣體切割和焊接用的鎢極 編碼 | Tungsten electrodes for inert gas shielded arc welding and for plasma cutting and welding- Codification (ISO 6848:1984) |
| EN 28846-1993+A1-2000 | 小艇 電氣裝置 周圍可燃氣體的防燃防護 | Small craft; electrical devices; protection against ignition of surrounding flammable gases (ISO 8846:1990) |
| EN 308-1997 | 熱交換器 對空氣和煙道氣體熱恢復裝置建立空氣性能的試驗過程 | Heat exchangers - Test procedures for establishing performance of air to air and flue gases heat recovery devices |
| EN 334-1999+A1-2000 | 入口壓力不超過100 bar的氣體壓力調節器 | Gas pressure regulators for inlet pressures up to 100 bar |
| EN 371-1992 | 呼吸保護設備 抗低沸點有機化合物的AX氣體過濾器和綜合過濾器 要求、測試、標志 | Respiratory protective devices; AX gas filters and combined filters against low boiling organic compounds; requirements, testing, marking |
| EN 372-1992 | 呼吸保護設備 抗特定化合物的SX氣體過濾器和綜合過濾器 要求、測試、標志 | Respiratory protective devices; SX gas filters and combined filters against specific named compounds; requirements, testing, marking |
| EN 377-1993 | 使用工業過程中應用的可燃氣體以外氣體的器具及有關控制裝置應用的潤滑劑 | Lubricants for applications in appliances and associated controls using combustible gases except those designed for use in industrial processes |
| EN 405-2001 | 呼吸保護設備 防氣體或防氣體和顆粒的閥濾式半面罩 要求、測試和標志 | Respiratory protective devices - Valved filtering half masks to protect against gases or gases and particles - Requirements, testing, marking |
| EN 437-2003 | 試驗氣體 試驗壓力 器具分類 | Test gases - Test pressures - Appliance categories |
| EN 439-1994 | 焊接消耗品 電弧焊和切割用保護氣體 | Welding consumables - Shielding gases for arc welding and cutting |
| EN 440-1994 | 焊接消耗品 非合金與細粒鋼的氣體保護金屬電弧焊用絲狀電極和沉積物 分類 | Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification |
| EN 45544-1-1999 | 工作場所 有毒氣體和蒸氣的直接檢測和直接濃度測量用電氣設備 第1部分：試驗方法和一般要求 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 1: General requirements and test methods |
| EN 45544-2-1999 | 工作場所 有毒氣體和蒸氣的直接檢測和直接濃度測量用電氣設備 第2部分：極限值域內濃度測量用設備的性能 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 2: Performance requirements for apparatus used for measuring concentrations in the region of limit values |
| EN 45544-3-1999 | 工作場所 有毒氣體和蒸氣的直接檢測和直接濃度測量用電氣設備 第3部分：大大超過極限值的濃度測量用設備 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 3: Performance requirements for apparatus used for measuring concentrations well above limit values |
| EN 45544-4-1999 | 工作場所 有毒氣體和蒸氣的直接檢測和直接濃度測量用電氣設備 第4部分：.選擇、安裝、使用和維修的指南 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 4: Guide for selection, installation, use and maintenance |
| EN 50107-1-2002 | 無荷載額定輸出電壓大于1kV小于10kV的標志燈和氣體放電管裝置 第1部分：一般要求 | Signs and luminious-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV - Part 1: General requirements / Note: To be amended by EN 50107-1/prA1 (2003-09). |
| EN 50143-1997+A1-2003 | 無荷載額定輸出電壓大于1KV小于10KV的標志燈和氣體放電管裝置用電纜 | Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV |
| EN 50194-2000 | 探測房屋內易燃氣體的電氣裝置 測試方法及性能要求 | Electrical apparatus for the detection of combustible gases in domestic premises - Test methods and performance requirements |
| EN 50241-1-1999 | 可燃或毒性氣體和蒸氣的檢測用開路儀器規范 第1部分：一般要求和試驗方法 | Specification for open path apparatus for the detection of combustible or toxic gases and vapours - Part 1: General requirements and test methods |
| EN 50241-2-1999 | 可燃或毒性氣體和蒸氣的檢測用開路儀器規范 第2部分：可燃氣體檢測用儀器的性能要求 | Specification for open path apparatus for the detection of combustible or toxic gases and vapours - Part 2: Performance requirements for apparatus for the detection of combustible gases |
| EN 50244-2000 | 家用易燃氣體探測用電氣設備 選擇、安裝、使用和維修指南 | Electrical apparatus for the detection of combustible gases in domestic premises - Guide on the selection, installation, use and maintenance |
| EN 50267-1-1998 | 在著火條件下電纜的一般測試方法 電纜材料燃燒過程中放出氣體的試驗 第1部分：裝置 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Part 1: Apparatus |
| EN 50267-2-1-1998 | 在著火條件下電纜的一般測試方法 電纜材料燃燒過程中放出氣體的試驗 第2-1部分：程序 氫鹵酸氣體量的測 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Part 2-1: Procedures - Determination of the amount of halogen acid gas |
| EN 50267-2-2-1998 | 在著火條件下電纜的一般測試方法 電纜材料燃燒過程中放出氣體的試驗 第2-2部分：程序 通過測量 pH 值和 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Part 2-2: Procedures - Determination of degree of acidity of gases for materials by measuring pH and conductivity |
| EN 50267-2-3-1998 | 在著火條件下電纜的一般測試方法 電纜材料燃燒過程中放出氣體的試驗 第2-3部分：程序 通過測量 pH 值和 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Part 2-3: Procedures - Determination of degree of acidity of gases for cables by determination of the weighted average of pH and conductivity Partly Supersedes HD602S1:1992 |
| EN 50270-1999 | 電磁兼容性 探測和測量易燃氣體、有毒氣體或氧氣的電氣裝置 | Electromagnetic compatibility - Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen |
| EN 50271-2001 | 探測和測量易燃氣體、有毒氣體或氧氣的電氣裝置 使用軟件和（或）數字技術裝置的要求和測試 | Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen - Requirements and tests for apparatus using software and/or digital technologies |
| EN 60068-2-60-1996 | 環境試驗 第2-60部分：試驗方法 試驗Ke：流動混合氣體的腐蝕試驗 | Environmental testing - Part 2: Tests - Test Ke: Flowing mixed gas corrosion test (IEC 60068-2-60:1995) |
| EN 60079-15-2003 | 爆炸氣體用電氣設備 第15部分：防護類型n | Electrical apparatus for explosive gas atmospheres - Part 15: Type of protection "n" (IEC 60079-15:2001, modified) |
| EN 60079-7-2003 | 爆炸氣體用電氣設備 第7部分：增強安全性e | Electrical apparatus for explosive gas atmospheres - Part 7: Increased safety "e" (IEC 60079-7:2001) / Note: Endorsement notice |
| EN 60512-11-14-1997 | 電子設備用機電元件 基本試驗規程和測量方法 第11部分：氣候試驗 第14節：試驗11p 流動的單種氣體腐蝕 | Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 14: Test 11p: Flowing single gas corrosion test (IEC 60512-11-14:1996) |
| EN 60512-11-7-2003 | 電子設備用連接器 基本和測量 氣候試驗 第11-7部分：試驗11g 流動混合氣體腐蝕性試驗 | Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests; Test 11g: Flowing mixed gas corrosion test (IEC 60512-11-7:2003) / Note: Endorsement notice |
| EN 60517-1996+A11-1999 | 額定電壓72.5kv及以上的氣體絕緣的金屬封閉開關設備 | Gas-insulated metal-enclosed switchgear for rated voltages of 72,5 kV and above (IEC 60517:1990 + Corrigendum 1995 + A1:1994) |
| EN 60567-1992 | 充油電氣設備中氣體和油取樣及游離和溶解氣體分析指南 | Guide for the sampling of gases and of oil from oil-filled electrical equipment and for the analysis of free and dissolved gases (IEC 60567:1992) |
| EN 60599-1999 | 礦物油浸漬的電氣設備 不溶解的和自由氣體分析說明指南 | Mineral oil-impregnated electrical equipment in service - Guide to the interpretation of dissolved and free gases analysis (IEC 60599:1999) |
| EN 60749-7-2002 | 半導體器件 機械和氣候試驗方法 第7部分：內部含水量測量和其它殘留氣體分析 | Semiconductor devices - Mechanical and climatic test methods - Part 7: Internal moisture content measurement and the analysis of other residual gases (IEC 60749-7:2002) / Note: Endorsement notice |
| EN 61010-2-042-1997 | 測量、控制和實驗室用電氣設備的安全要求 第2－042部分：醫用材料處理及實驗室加工用毒性氣體蒸壓器和消毒 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-042: Particular requirements for autoclaves and sterilizers using toxic gas for the treatment of medical materials, and for laboratory processes (IEC 61010) |
| EN 61010-2-043-1997 | 測量、控制和實驗室用電氣設備的安全要求 第2－043部分：醫用材料處理及實驗室加工用熱空氣或熱惰性氣體干 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-043: Particular requirements for dry heat sterilizers using either hot air or hot inert gas for the treatment of medical materials, and for laboratory proc |
| EN 61181-1993 | 浸漬絕緣材料 溶解氣體分析(DGA)應用于電氣設備的工廠試驗 | Impregnated insulating materials - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment (IEC 61181:1993) |
| EN 61207-1-1994 | 氣體分析器的性能表示 第1部分：總則 | Expression of performance of gas analyzers; part 1: general (IEC 61207-1:1994) |
| EN 61207-2-1994 | 氣體分析器的性能表示 第2部分：氣體中的氧(利用高溫電化學傳感器) | Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors) (IEC 61207-2:1994) |
| EN 61207-3-2002 | 氣體分析器 性能表示 第3部分：順磁氧氣分析器 | Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers (IEC 61207-3:2002) / Note: Endorsement notice |
| EN 61207-3/prA1-1999 | 氣體分析器 性能表示 第3部分：順磁氧氣分析器 修改prA1 | Amendment 1 to IEC 61207-3: Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers |
| EN 61207-6-1994 | 氣體分析器的性能表示 第6部分：光度分析器 | Expression of performance of gas analyzers - Part 6: Photometric analyzers (IEC 61207-6:1994) |
| EN 61347-2-10-2001 | 燈的控制裝置 第2-10部分：高頻冷起動管形氣體放電燈(霓虹燈管)用電子逆變器和變流器的特殊要求 | Lamp controlgear - Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) (IEC 61347-2-10:2000) |
| EN 61347-2-9-2001 | 燈的控制裝置 第2-9部分：氣體放電燈(熒光燈除外)用鎮流器的特殊要求 | Lamp controlgear - Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) (IEC 61347-2-9:2000) |
| EN 61347-2-9/prA1-2003 | 燈的控制裝置 第2-9部分：氣體放電燈(熒光燈除外)用鎮流器的特殊要求 修改prA1 | IEC 61347-2-9, Am. 1: Lamp controlgear - Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) |
| EN 61643-311-2001 | 低壓浪涌保護裝置元件 第311部分：氣體放電管規范 | Components for low-voltage surge protective devices - Part 311: Specifications for gas discharge tubes (GDT) (IEC 61643-311:2001) |
| EN 61779-1-2000 | 可燃性氣體的檢測和測量用電氣設備 第1部分：一般要求和試驗方法 | Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods (IEC 61779-1:1998, modified) |
| EN 61779-2-2000 | 可燃性氣體的檢測和測量用電氣設備 第2部分：指示空氣中甲烷體積百分率最大為5%的I類設備的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Part 2: Performance requirements for group I apparatus indicating a volume fraction up to 5 % methane in air (IEC 61779-2:1998, modified) |
| EN 61779-3-2000 | 可燃性氣體的檢測和測量用電氣設備 第3部分：指示空氣中甲烷體積百分率最大為100%的I類設備的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Part 3: Performance requirements for group I apparatus indicating a volume fraction up to 100 % methane in air (IEC 61779-3:1998, modified) |
| EN 61779-4-2000 | 可燃性氣體的檢測和測量用電氣設備 第4部分：指示體積百分率最大為100%低爆炸物極限的II類設備的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating a volume fraction up to 100 % lower explosive limit (IEC 61779-4:1998, modified) |
| EN 61779-5-2000 | 可燃性氣體的檢測和測量用電氣設備 第5部分：指示氣體體積百分率最大為100%的II類設備的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Part 5: Performance requirements for group II apparatus indicating a volume fraction up to 100 % gas (IEC 61779-5:1998, modified) |
| EN 621-1998+A1-2003 | 無風扇支持燃燒氣體及/或燃燒物質移動、凈熱輸入功率不超過300kW的空間加熱用非家用燃氣強制對流空氣加熱器 | Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products |
| EN 676-2003 | 氣體燃料用自動強制鼓風燃燒器 | Automatic forced draught burners for gaseous fuels |
| EN 682-2002 | 彈性密封件 用于運送氣體和碳氫化合物液體的管道和配件的密封件的材料要求 | Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids |
| EN 717-2-1994 | 木基板 甲醛釋放量的測定 第2部分：用氣體分析法測定甲醛釋放量 | Wood-based panels - Determination of formaldehyde release - Part 2: Formaldehyde release by the gas analysis method |
| EN 720-1-1999 | 可運輸氣瓶 氣體和氣體混合物 第1部分：純氣體的特性 | Transportable gas cylinders - Gases and gas mixtures - Part 1: Properties of pure gases |
| EN 720-2-1996 | 可移動氣瓶 氣體和氣體混合物 第2部分：氣體和氣體混合物的可燃性和氧化能力測定 | Transportable gas cylinders - Gases and gas mixtures - Part 2: Determination of flammability and oxidizing ability of gases and gas mixtures |
| EN 725-3-1994 | 先進技術陶瓷 陶瓷粉的試驗方法 第3部分：帶運載氣體的熱萃取法測定非氧化物中氧的含量 | Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas |
| EN 737-1-1998 | 醫療氣體管道系統 第1部分：壓縮醫療氣體和真空用終端設備 | Medical gas pipeline systems - Part 1: Terminal units for compressed medical gases and vacuum |
| EN 737-2-1998+A1-1999+AC-2000 | 醫療氣體管道系統 第2部分：麻醉氣體凈化處理系統 基本要求 | Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems - Basic requirements |
| EN 737-3-1998+A1-1999+AC-2000 | 醫療氣體管道系統 第3部分：壓縮醫療氣體和真空用管道 | Medical gas pipeline systems - Part 3: Pipelines for compressed medical gases and vacuum |
| EN 737-4-1998 | 醫療氣體管道系統 第4部分：麻醉氣體凈化系統的終端設備 | Medical gas pipeline systems - Part 4: Terminal units for anaesthetic gas scavenging systems |
| EN 738-1-1997+A1-2002 | 醫用氣體用壓力調節器 第1部分：壓力調節器和有流量計裝置的壓力調節器 | Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow metering devices |
| EN 738-2-1998 | 醫用氣體用壓力調節器 第2部分：多管和單管壓力調節器 | Pressure regulators for use with medical gases - Part 2: Manifold and line pressure regulators |
| EN 738-3-1998+A1-2002 | 醫用氣體用壓力調節器 第3部分：帶氣瓶閥的壓力調節器 | Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves |
| EN 738-4-1998+A1-2002 | 醫用氣體用壓力調節器 第4部分：醫療設備用低壓壓力調節器 | Pressure regulators for use with medical gases - Part 4: Low-pressure regulators intended for incorporation into medical equipment |
| EN 739-1998+A1-2002 | 醫療氣體設備用低壓軟管組件 | Low-pressure hose assemblies for use with medical gases |
| EN 746-3-1997 | 工業熱處理設備 第3部分：環境氣體產生和使用的安全要求 | Industrial thermoprocessing equipment - Part 3: Safety requirements for the generation and use of atmosphere gases |
| EN 758-1997 | 焊接消耗品 帶和不帶氣體保護殼的非合金鋼及細粒鋼金屬電弧焊接用管狀芯焊條 分類 | Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels - Classification |
| EN 778-1998+A1-2001 | 無風扇支持燃燒氣體及/或燃燒物質移動、凈熱輸入功率不超過70kW的空間加熱用家用氣體燃燒強制對流空氣加熱 | Domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 70 kW, without a fan to assist transportation of combustion air and/or combustion products |
| EN 838-1995 | 工作場所的空氣 測定氣體和水蒸汽用的擴散取樣器 要求和試驗方法 | Workplace atmospheres - Diffusive samplers for the determination of gases and vapours - Requirements and test methods |
| EN 874-1995 | 氣焊設備 圓柱筒焊接用氧/燃料氣體焊炬（切割機型） 結構型式、一般規范和試驗方法 | Gas welding equipment - Oxygen/fuel gas blowpipes (cutting machine type) of cylindrical barrel - Type of construction, general specifications, test methods |
| EN 993-4-1995 | 成形致密耐火制品的試驗方法 第4部分：氣體滲透性測定 | Methods of test for dense shaped refractory products - Part 4: Determination of permeability to gases |
| EN ISO 10062-1995 | 人工環境中低濃度污染氣體腐蝕程度的試驗 | Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es) (ISO 10062:1991) |
| EN ISO 10882-1-2001 | 焊接和相關工藝的衛生與安全 工作人員呼吸區域中空氣中懸浮顆粒物及氣體的取樣 第1部分：空氣中粒子取樣 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operators breathing zone - Part 1: Sampling of airborne particles (ISO 10882-1:2001) |
| EN ISO 10882-2-2000 | 焊接和相關工藝的衛生與安全 工作人員呼吸區域中空氣中懸浮顆粒物及氣體的取樣 第2部分：氣體取樣 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operatiors breathing zone - Part 2: Sampling of gases (ISO 10882-2:2000) |
| EN ISO 11114-1-1997+AC-1998 | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第1部分：金屬材料 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 1: Metallic materials (ISO 11114-1:1997) |
| EN ISO 11114-2-2000 | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第2部分：非金屬材料 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2000) |
| EN ISO 11114-3-1997 | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第3部分：氧環境中自燃試驗 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test in oxygen atmosphere (ISO 11114-3:1997) |
| EN ISO 11196-1997 | 麻醉氣體監視器(包括技術勘誤1) | Aneasthetic gas monitors (ISO 11196:1995 including Technical Corrigendum 1:1997) |
| EN ISO 1183-3-1999 | 塑料 非泡沫塑料的密度測定方法 第3部分：氣體比重瓶法 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999) |
| EN ISO 12569-2000 | 建筑物熱性能 建筑物的換氣率測定 示蹤氣體稀釋法 | Thermal insulation in buildings - Determination of air change in buildings - Tracer gas dilution method (ISO 12569:2000) |
| EN ISO 13631-2002 | 石油和天然氣工業 整裝往復式氣體壓縮機 | Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002) |
| EN ISO 15011-1-2002 | 焊接和有關工藝中的衛生和安全 電弧焊產生的煙塵和氣體取樣的實驗室方法 第1部分：顆粒煙塵分析取樣和產 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 1: Determination of emission rate and sampling for analysis of particulate fume (ISO 15011-1:2002) |
| EN ISO 15011-2-2003 | 焊接和有關工藝中的健康和安全 電弧焊產生的煙塵和氣體取樣的實驗室方法 第2部分：除臭氧外、各種氣體產 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone (ISO 15011-2:2003) |
| EN ISO 15011-3-2002 | 焊接和有關工藝中的健康和安全 電弧焊產生的煙塵和氣體取樣的實驗室方法 第3部分：在固定點測定臭氧濃度 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3: Determination of ozone concentration using fixed point measurements (ISO 15011-3:2002) |
| EN ISO 6551-1995 | 石油液體和氣體 動態測量的精度和可靠性 電脈沖數據和／或電子脈沖數據的電纜傳輸 | Petroleum liquids and gases - Fidelity and security of dynamic measurement - Cabled transmission of electric and/or electronic pulsed data (ISO 6551:1982) |
| EN ISO 8178-1-1996 | 往復式內燃機 排放測量 第1部分：氣體和顆粒排放物的試驗臺測量 | Reciprocating internal combustion engines - Exhaust emission measurement - Part 1: Test-bed measurement of gaseous and particulate exhaust emissions (ISO 8178-1:1996) |
| EN ISO 8178-2-1996 | 往復式內燃機 排放測量 第2部分：氣體和顆粒排放物的現場測量 | Reciprocating internal combustion engines - Exhaust emission measurement - Part 2: Measurement of gaseous and particulate exhaust emissions at site (ISO 8178-2:1996) |
| EN ISO 8974-2002 | 塑料 酚醛樹脂 用氣體色譜法測定殘余酚含量 | Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography (ISO 8974:2002) |
| EN ISO 9300-1995 | 用文杜利臨界流量噴嘴測定氣體流量 | Measurement of gas flow means of critical flow Venturi nozzles (ISO 9300:1990) |
| EN ISO 9360-1-2000 | 麻醉和呼吸設備 用于加濕人的呼吸氣體的熱濕交換器(HMEs) 第1部分：與250ml最小潮量一起使用的熱濕交換器 | Anaesthetic and respiratory equipment - Heat and moisture exchangers (HMEs) for humidifying respired gases in humans - Part 1: HMEs for use with minimum tidal volumes of 250 ml (ISO 9360-1:2000) |
| EN ISO 9360-2-2002 | 麻醉和呼吸設備 用于加濕人的呼吸氣體的熱濕交換器(HMEs) 第2部分：最小落差容量為250ml的氣管造口病人用 | Anaesthetic and respiratory equipment - Heat and moisture exchangers (HMEs) for humidifying respired gases in humans - Part 2: HMEs for use with tracheostomized patients having minimum tidal volumes of 250 ml (ISO 9360-2:2001) |
| EN ISO 9692-3-2001 | 焊接和相關工藝 接頭制備的建議 第3部分：鋁及鋁合金的金屬焊條惰性氣體保護焊和鎢焊條惰性氣體保護焊 | Welding and allied processes - Recommendations for joint preparation - Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 9692-3:2000) |
| ENV 12290-1996 | 高級工藝業陶瓷 惰性氣體環境下陶瓷合成物的高溫機械特性 壓縮特性的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of compression properties |
| ENV 1259-1-1994 | 單個氣體燃燒器架空輻射管加熱器和非家用氣體架空光源加熱器 第1部分：為建立合理利用能量的要求和試驗方 | Single burner gas-fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters; part 1: requirements and test methods for establishing the rational use of energy; radiometric method A |
| ENV 1259-2-1996 | 單個氣體燃燒器架空輻射管加熱器和非家用氣體架空光源加熱器 第2部分：為建立合理利用能量的要求和試驗方 | Single burner gas-fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters - Part 2: Requirements and test methods for establishing the rational use of energy - Radiometric method B |
| ENV 1259-3-1996 | 單個氣體燃燒器架空輻射管加熱器和非家用氣體架空光源加熱器 第3部分：為建立合理利用能量的要求和試驗方 | Single burner gas-fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters - Part 3: Requirements and test methods for establishing the rational use of energy - Radiometric method C |
| ENV 12788-1998 | 高級工藝陶瓷 惰性氣體中陶瓷合成物的高溫機械性能 抗彎強度測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of flexural strength |
| ENV 13235-1998 | 高級工藝陶瓷 陶瓷合成物 惰性氣體中陶瓷合成物的高溫機械性能 蠕變性測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of creep behaviour |
| ENV 14459-2002 | 電子設備用于煤氣灶和氣體燃燒設備的危險分析和建設的方法 | Method of risk analysis and recommendations for the use of electronics in systems for control of gas burners and gas burning appliances |
| ENV 1892-1996 | 先進技術陶瓷 在高溫惰性氣體下陶瓷合成材料的機械性能 抗拉伸性能的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties |
| ENV 1894-1996 | 先進技術陶瓷 惰性氣體中高溫下陶瓷合成材料的機械性能 通過對切口樣品壓縮加載測定剪切強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens |
| ENV 737-6-2003 | 醫療氣體管道系統 第6部分：壓縮醫療氣體和真空用終端部件用探針的尺寸 | Medical gas pipeline systems - Part 6: Dimensions and allocation of probes for terminal units for compressed medical gases and vacuum |
| HD 22.13 S1-1996+A1-2000 | 額定電壓450/750V及以下的橡膠絕緣電纜 第13部分：煙霧和腐蝕性氣體低排放的絕緣和交聯聚合物單芯和多芯軟 | Rubber insulated cables of rated voltages up to and including 450/750 V - Part 13: Single and multicore flexible cables, insulated and sheathed with crosslinked polymer and having low emission of smoke and corrosive gases |
| HD 22.9 S2-1995+A1-1999 | 額定電壓450/750V及以下的橡膠絕緣電纜 第9部分：煙霧和腐蝕性氣體低排放的固定配線用單芯非鎧裝電纜 | Rubber insulated cables of rated voltages up to and including 450/750 V - Part 9: Single core non-sheathed cables for fixed wiring having low emission of smoke and corrosive gases |
| prEN 12094-4-2001 | 固定式消防系統 氣體滅火系統的部件 第4部分：對高壓容器閥組件及其驅動器的要求及試驗方法 | Fixed fire fighting systems - Components for gas extinguishing systems - Part 4: Requirements and test methods for high pressure container valve assemblies and their actuators |
| prEN 12411-1-1996 | 工廠環境 直接探測有毒氣體和蒸氣及直接測量其濃度的電子設備 第1部分：一般要求和試驗方法 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 1: General requirements and test methods |
| prEN 12411-2-1996 | 工廠環境 直接探測有毒氣體和蒸氣及直接測量其濃度的電子設備 第2部分：用于測量極限值范圍內濃度的設 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 2: Performance requirements for apparatus used for measuring concentrations in the range of limit values |
| prEN 12411-3-1996 | 工作場所的氣體 直接探測有毒氣體和蒸氣直接測量其濃度用的電氣儀表 第3部分：用于測量遠大于極限值的 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of polluting gases and vapours - Part 3: Performance requirements for apparatus used for measuring concentrations well above limit values |
| prEN 12411-4-1997 | 工作場所的氣體 工廠環境 直接探測有毒氣體和蒸氣及直接測量其濃度的電子設備 第4部分：選擇、安裝、 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Part 4: Guide for selection, installation, use and maintenance |
| prEN 13096-2003 | 可移動氣瓶 向容器中充氣的條件 單成分氣體 | Transportable gas cylinders - Conditions for filling gases into receptables - Single component gases |
| prEN 13099-2003 | 可移動氣瓶 向容器中充入氣體混合物的條件 | Transportable gas cylinders - Conditions for filling gas mixtures into receptacles |
| prEN 13528-3-2003 | 環境空氣質量 測定氣體和蒸氣濃度的擴散取樣器 要求和試驗方法 第3部分：選擇、使用和維修指南 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Part 3: Guide to selection, use and maintenance |
| prEN 13631-16-2002 | 民用炸藥 烈性炸藥 第16部分：有毒氣體的探測和測量 | Exlosives for civil uses - High explosives - Part 16: Detection and measurement of toxic gases |
| prEN 14208-2003 | 可運輸氣瓶 氣體運輸用容積達3000升的焊接氣罐規范 設計和結構 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| prEN 14291-2001 | 氣體裝置泄漏檢測用起泡液 | Foam producing solutions for leak detection on gas installation |
| prEN 14387-2003 | 呼吸保護裝置 氣體過濾器和組合過濾器 要求、試驗和標志 | Respiratory protective devices - Gas filter(s) and combined filter(s) - Requirements, testing, marking / Note: Intended as replacement for EN 141 (2000-02), EN 371 (1992-03), EN 372 (1992-03). |
| prEN 14412-2002 | 室內空氣質量 氣體和蒸氣濃度的測定用擴散取樣器 選擇、使用和維護的指南 | Indoor air quality - Diffusive samplers for the determination of concentration of gases and vapours - Guide for selection, use and maintenance |
| prEN 1555-6-1995 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第6部分：推薦的安裝實踐 | Plastics piping systems for gaseous fuels supply - Polyethylene (PE) - Part 6: Recommended practice for installation |
| prEN 203-1-2002 | 氣體加熱供膳設備 第1部分：安全要求 | Gas heated catering equipment - Part 1: safety requirements |
| prEN 203-3-1996 | 氣體加熱供膳設備 第3部分：適應性目的 | Gas-heated catering equipment - Part 3: Fitness for purpose |
| prEN 2445-1998 | 航空航天系列 氣體熔化鋼FE-PL8201 (41NiCrMo2) 調質的 鍛件 D<(Index)e> 45 mm - 900 MP | Aerospace series - Steel FE-PL8201 (41NiCrMo2) air melted - Hardened and tempered - Forgings - D<(Index)e> 45 mm - 900 MPa R<(Index)m> 1100 MPa |
| prEN 2469-1998 | 航空航天系列 氣體熔化鋼FE-PA3901 (X1CrNi18-10) 軟化的 鋼絲 0,4 D 12,5 m | Aerospace series - Steel FE-PA3901 (X1CrNi18-10) air melted - Softened - Wires - 0,4 D 12,5 mm - 450 MPa R<(Index)m> 650 MPa |
| prEN 2475-1998 | 航空航天系列 氣體熔化鋼FE-PL2106 (30CrNiMo8) 調質的 機械加工用棒材 D<(Index)e> 100 m | Aerospace series - Steel FE-PL2106 (30CrNiMo8) air melted - Hardened and tempered - Bar for machining - D<(Index)e> 100 mm - 1100 MPa R<(Index)m> 1300 MPa |
| prEN 2538-1999 | 航空航天系列 經溶液處理和淀積處理氣體熔化鋼 FE-PM3801 (X5CrNiCu17-4) 薄板材和帶材 a 6 | Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) air melted, solution treated and precipitation treated - Sheet and strip a 6 mm, Rm≥ 1310 MPa |
| prEN 2539-1999 | 航空航天系列 經溶液處理和淀積處理氣體熔化鋼 FE-PM3801 (X5CrNiCu17-4) 棒材a or D 200 mm | Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) air melted, solution treated and precipitation treated - Bar a or D 200 mm, Rm≥ 965 MPa |
| prEN 2540-1997 | 航空航天系列 經溶液處理和淀積處理氣體熔化鋼 FE-PM3902 (X7CrNiCu17-7) 薄板材和帶材 a 6 | Aerospace series - Steel FE-PM3902 (X7CrNiAl17-7) air melted, solution treated and precipitation hardened - Sheet and strip - a 6 mm, 1240 MPa R<(Index)m> 1450 MPa |
| prEN 332-1990 | 壓力不超過PN 0,2 和壓力為DN 15 至DN 50間的家用氣體裝置用封閉底人工操縱金屬錐形旋塞關閉閥 | Manually operated metallic taper plug shut-off valves with closed bottom for domestic gas installations for pressures up to PN 0,2 and with DN 15 to DN 50 |
| prEN 333-1990 | 壓力不超過PN 4 和壓力為DN 15 至DN 50間的家用氣體裝置用人工操縱金屬球關閉閥 | Manually operated metallic ball shut-off valves for domestic gas installations up to PN 4 and with DN 15 to DN 50 |
| prEN 50039-2001 | 潛在爆炸性環境用防爆電氣設備 固有安全電氣系統 i" 爆炸氣體用 II 類系統 | Electrical apparatus for potentially explosive atmospheres - Intrinsically safe electrical systems "i" - Group II systems for gas atmospheres |
| prEN 50276-1997 | 牽引蓄電池產生的氣體發射 封閉式充電區的通風和安全要求 | Gaseous emissions produced by traction batteries - Ventilation and general safety requirements for closed charging areas |
| prEN 60512-11-14-2003 | 電子設備用連接器 試驗和測量 第11-14部分：氣候試驗 試驗11p：一種流動氣體的腐蝕試驗 | Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests; Test 11p: Flowing single gas corrosion test |
| prEN 61647-1-2001 | 低壓浪涌保護裝置元件 第1部分：氣體放電管規范 | IEC 61647-1, Ed. 1: Components for low-voltage surge protective devices - Part 1: Specification for gas discharge tubes (GDT) |
| prEN 62271-200-2003 | 氣體絕緣金屬外殼的開關設備 第200部分：最高電壓達72.5KV及以上的設備 | IEC 62271-200, Ed. 1: High-voltage switchgear and controlgear - Part 200: A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| prEN ISO 1183-4-1998 | 塑料 非泡沫塑料的密度測定方法 第4部分：氣體比重瓶法 | Plastics - Methods for determining the density of non-cellular plastics - Part 4: Gas pyknometer method (ISO/DIS 1183-4:1998) |
| prEN ISO 14520-1-2000 | 氣體滅火系統 物理特性和系統設計 第1部分：一般要求 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 1: General requirements (ISO/FDIS 14520-1:2000) |
| prEN ISO 14520-10-2000 | 氣體滅火系統 物理特性和系統設計 第10部分：HFC 23滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 10: HFC 23 extinguishant (ISO/FDIS 14520-10:2000) |
| prEN ISO 14520-11-2000 | 氣體滅火系統 物理特性和系統設計 第11部分：HFC 236fa滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 11: HFC 236fa extinguishant (ISO/FDIS 14520-11:2000) |
| prEN ISO 14520-12-2000 | 氣體滅火系統 物理特性和系統設計 第12部分： IG-01滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 12: IG-01 extinguishant (ISO/FDIS 14520-12:2000) |
| prEN ISO 14520-13-2000 | 氣體滅火系統 物理特性和系統設計 第13部分： IG-100滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 13: IG-100 extinguishant (ISO/FDIS 14520-13:2000) |
| prEN ISO 14520-14-2000 | 氣體滅火系統 物理特性和系統設計 第14部分： IG-55滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 14: IG-55 extinguishant (ISO/FDIS 14520-14:2000) |
| prEN ISO 14520-15-2000 | 氣體滅火系統 物理特性和系統設計 第15部分： IG-541滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 15: IG-541 extinguishant (ISO/FDIS 14520-15:2000) |
| prEN ISO 14520-2-2000 | 氣體滅火系統 物理特性和系統設計 第2部分：CF3I滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 2: CF3I extinguishant (ISO/FDIS 14520-2:2000) |
| prEN ISO 14520-3-2000 | 氣體滅火系統 物理特性和系統設計 第3部分：FC-2-1-8滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 3: FC-2-1-8 extinguishant (ISO/FDIS 14520-3:2000) |
| prEN ISO 14520-4-2000 | 氣體滅火系統 物理特性和系統設計 第4部分：FC-3-1-10滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 4: FC-3-1-10 extinguishant (ISO/FDIS 14520-4:2000) |
| prEN ISO 14520-5-1998 | 氣體滅火系統 物理特性和系統設計 第5部分： FC-5-1-14滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 5: FC-5-1-14 extinguishant (ISO/DIS 14520-5:1998) |
| prEN ISO 14520-6-2000 | 氣體滅火系統 物理特性和系統設計 第6部分： HCFC混合A的滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 6: HCFC Blend A extinguishant (ISO/FDIS 14520-6:2000) |
| prEN ISO 14520-7-2000 | 氣體滅火系統 物理特性和系統設計 第7部分：HCFC 124滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 7: HCFC 124 extinguishant (ISO/FDIS 14520-7:2000) |
| prEN ISO 14520-8-2000 | 氣體滅火系統 物理特性和系統設計 第8部分：HFC 125滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 8: HFC 125 extinguishant (ISO/FDIS 14520-8:2000) |
| prEN ISO 14520-9-2000 | 氣體滅火系統 物理特性和系統設計 第9部分：HFC 227ea滅火劑 | Gaseous fire-extinguishing systems - Physical properties and system design - Part 9: HFC 227ea extinguishant (ISO/FDIS 14520-9:2000) |
| prEN ISO 15002-1996 | 醫用氣體管道系統終端裝置用氣流量測量裝置 | Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO/DIS 15002:1996) |
| prEN ISO 9692-1-2003 | 焊接和相關工藝 接頭制備的推薦工藝 第1部分：鋼的人工電弧焊、氣體保護金屬電弧焊、氣焊和束焊 | Welding and allied processes - Recommendations for joint preparation - Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels (ISO/FDIS 9692-1:2003) |
| 編號 | 中文名稱 | 英文名稱 |