| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| IEC 61073-1-2009 | 纖維光學互連器件和無源元件.光學纖維和光纜用機械接頭和熔融接頭保護器.第1部分:通用規范 | Fibre optic interconnecting devices and passive components - Mechanical splices and fusion splice protectors for optical fibres and cables - Part 1: Generic specification |
| IEC 61076-3-114-2009 | 電子設備用連接器.產品要求.第3-114部分:矩形連接器.合并IEC 60603-7系列接口的工業環境用頻帶在600MHz以下 | Connectors for electronic equipment - Product requirements - Part 3-114: Rectangular connectors - Detail specifications for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface - Variant 11 related to IEC 61076-3-106 - Bayonet coupling type |
| IEC 61188-5-8-2007 | 印制板和印制板組件.設計和使用.第5-8部分:附件(結合區/接頭)考慮要素.區域陣列組件(BGA, FBGA, CGA, LGA) | Printed boards and printed board assemblies - Design and use - Part 5-8: Attachment (land/joint) considerations - Area array components (BGA, FBGA, CGA, LGA) |
| IEC 62275-2006 | 電纜管理系統.電器設備用電纜接頭 | Cable management systems - Cable ties for electrical installations |
| ISO 10042 Technical Corrigendum 1-2006 | 焊接.鋁和鋁合金的弧焊接頭.缺陷質量分級.技術勘誤1 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections; Technical Corrigendum 1 |
| ISO 10042-2005 | 焊接 鋁和鋁合金的弧焊接頭 缺陷質量分級指南 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections |
| ISO 1022-1988 | 航空航天 流體系統用氣態氧充氣接頭(舊型) 尺寸(英制系列) | Aerospace; gaseous oxygen replenishment connection for use in fluid systems (old type); dimensions (inch series) |
| ISO 10321-2008 | 土工織物.用寬條法對接頭/接縫處的拉伸試驗 | Geosynthetics - Tensile test for joints/seams by wide-width strip method |
| ISO 1034-1973 | 航空器 地面空氣調節連接接頭 | Aircraft; Ground air-conditioning connections |
| ISO 10955-1999 | 航空航天 航空器操縱鋼絲繩用末端接頭和松緊套筒 技術規范 | Aerospace - End-fittings and turnbarrels for aircraft control wire rope - Technical specification |
| ISO 10983-1999 | 木結構 實心木材指型接頭 生產要求 | Timber structures - Solid timber finger-jointing - Production requirements |
| ISO 11-1987 | 航空器 壓力座艙的地面壓力試驗連接接頭 | Aircraft; Ground pressure testing connections for pressure cabins |
| ISO 11144-1995 | 牙科設備 供水及排水管接頭 | Dental equipment - Connections for supply and waste lines |
| ISO 1167-1-2006 | 流體傳輸用熱塑管、接頭和組件.抗內壓力的測定.第1部分:通用方法 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method |
| ISO 1167-2-2006 | 流體傳輸用熱塑管、接頭和組件.抗內壓力的測定.第2部分:管試件的準備 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces |
| ISO 12118-1995 | 航空貨運設備 全向額定承載能力等于或高于22250N(50001bf)的雙螺柱系留接頭的識別標志 | Air cargo equipment - Identification of double-stud tie-down fittings having an omnidirectional rated load capacity of 22250 N (5000 lbf) or above |
| ISO 12151-1-1999 | 液壓傳動和通用聯接件 軟管接頭 第1部分:帶ISO 8434-3 O形圈端面密封末端的軟管接頭 | Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends |
| ISO 12151-2-2003 | 液壓傳動和通用聯接件.軟管接頭.第2部分:帶ISO 8434-1 O形圈24錐形末端的軟管接頭 | Connections for hydraulic fluid power and general use - Hose fittings - Part 2: Hose fittings with ISO 8434-1 24° cone connector ends with O-rings |
| ISO 12151-3-1999 | 液壓傳動和通用聯接件 軟管接頭 第3部分:帶ISO6162法蘭末端的軟管接頭 | Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162 flange ends |
| ISO 12151-4-2007 | 用于液壓流體傳動和一般用途的接頭.軟管配件.第4部分:帶ISO 6149米制螺柱頭的軟管配件 | Connections for hydraulic fluid power and general use - Hose fittings - Part 4: Hose fittings with ISO 6149 metric stud ends |
| ISO 12151-5-2007 | 用于液壓流體傳動和一般用途的接頭.軟管配件.第5部分:帶ISO 8434-2 37°擴口端的軟管配件 | Connections for hydraulic fluid power and general use - Hose fittings - Part 5: Hose fittings with ISO 8434-2 37° flared ends |
| ISO 13486-1-1999 | 道路車輛 液壓制動系統 第1部分:雙喇叭口管、螺紋孔、陽螺紋管接頭和管座 | Road vehicles - Hydraulic braking systems - Part 1: Double-flare pipes, tapped holes, male fittings and tube seats |
| ISO 13919-1-1996 | 焊接 電子束和激光焊接頭 缺陷的質量分級指南 第1部分:鋼 | Welding - Electron and laser-beam welded joints - Guidance on quality levels for imperfections - Part 1: Steel |
| ISO 13919-2-2001 | 焊接 電子束和激光束焊接接頭 缺陷質量等級指南 第2部分：鋁及其可焊合金 | Welding - Electron and laser beam welded joints; Guidance on quality levels for imperfections - Part 2: Aluminium and its weldable alloys |
| ISO 13950 Technical Corrigendum 1-2008 | 塑料管和配件.電熔焊接頭的自動識別系統.技術勘誤1 | Plastics pipes and fittings - Automatic recognition systems for electrofusion joints; Technical Corrigendum 1 |
| ISO 13950-2007 | 塑料管和配件.電熔焊接頭的自動識別系統 | Plastics pipes and fittings - Automatic recognition systems for electrofusion joints |
| ISO 13953-2001 | 聚乙烯管材和管件 拉申強度的測定和熔接對接接頭試件的失效模型 | Polyethylene(PE) pipes and fittings - Determination of the tensile strengt and failure mode of test pieces from a butt-fused joint |
| ISO 14615-1997 | 粘合劑 結構型粘合劑粘結接頭的耐久性 荷載下暴露在濕度和溫度之中 | Adhesives - Durability of structural adhesive joints - Exposure to humidity and temperature under load |
| ISO 1465-1989 | 航空器 液態氧充填接頭 相配尺寸 | Aircraft; liquid oxygen replenishment couplings; mating dimensions |
| ISO 15171-1-1999 | 用于流體傳動和一般用途的管接頭 診斷用液壓管接頭 第1部分:非壓力下連接的管接頭 | Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 1: Coupling not for connection under pressure |
| ISO 15171-2-2000 | 用于流體傳動和一般用途的管接頭 診斷用液壓管接頭 第2部分:帶M16×2螺紋端的壓力連接接頭 | Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 × 2 end for connection under pressure |
| ISO 15236-4-2004 | 鋼絲傳送帶.第4部分:硫化帶接頭 | Steel cord conveyor belts - Part 4: Vulcanized belt joints |
| ISO 15407-1-2000 | 氣壓傳動 五氣口方向控制閥、規格18mm和26mm 第1部分:不帶電接頭的安裝面 | Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector |
| ISO 15509-2001 | 粘合劑 工程塑料接頭粘合強度的測定 | Adhesives - Determination of the bond strength of engineering-plastic joints |
| ISO 15614-8-2002 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第8部分:管對管板接頭焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints |
| ISO 15615-2002 | 氣焊設備.焊接、切割和相關工藝用乙炔復式接頭系統.高壓裝置的安全要求 | Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - Safety requirements in high-pressure devices |
| ISO 15835-1-2009 | 混凝土增強鋼.棒材制機械接頭用增強耦合器.第1部分:要求 | Steels for the reinforcement of concrete - Reinforcement couplers for mechanical splices of bars - Part 1: Requirements |
| ISO 15835-2-2009 | 混凝土加固用鋼.棒材機械接頭用加固連接件.第2部分:試驗方法 | Steels for the reinforcement of concrete - Reinforcement couplers for mechanical splices of bars - Part 2: Test methods |
| ISO 16028 AMD 1-2006 | 液壓傳動.在20MPa(200巴)至31.5MPa(315巴)壓力下使用的平面對接型快速接頭.規范.修改件1 | Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications; Amendment 1 |
| ISO 16028-1999 | 液壓傳動 用于壓力為20 MPa(200 bar)～31.5 MPa(315 bar)的平面對接型快速接頭 規范 | Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications |
| ISO 16070-2005 | 石油和天然氣工業.下井設備.鎖芯軸和落地接頭 | Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples |
| ISO 16422-2006 | 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于壓力下水運輸?shù)墓艿篮徒宇^.規范 | Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications |
| ISO 16670-2003 | 木結構.機械緊固件接頭.準靜態逆循環試驗方法 | Timber structures - Joints made with mechanical fasteners - Quasi-static reversed-cyclic test method |
| ISO 17636-2003 | 焊縫的無損檢驗.熔焊接頭的放射檢驗 | Non-destructive testing of welds - Radiographic testing of fusion-welded joints |
| ISO 17637-2003 | 焊縫的無損檢驗.熔焊接頭的外觀檢驗 | Non-destructive testing of welds - Visual testing of fusion-welded joints |
| ISO 17640-2005 | 焊接的無損檢驗.焊接接頭的超聲波檢驗 | Non-destructive testing of welds - Ultrasonic testing of welded joints |
| ISO 17653-2003 | 金屬材料接頭的破壞檢驗.電阻點焊的扭轉試驗 | Destructive tests on welds in metallic materials - Torsion test of resistance spot welds |
| ISO 17659-2002 | 焊接.圖示焊接接頭的多語種術語 | Welding - Multilingual terms for welded joints with illustrations |
| ISO 1813-1998 | 帶傳動 多楔帶、有接頭V帶、寬截面帶及六角帶 抗靜電帶的電導率:特性和試驗方法 | Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test |
| ISO 18279-2003 | 釬焊.釬焊接頭的缺陷 | Brazing - Imperfections in brazed joints |
| ISO 18672-1-2009 | 塑料無壓埋地排水管管道系統.聚酯混凝土(PRC).第1部分:連接管子和配件的柔性接頭. | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
| ISO 1966-1973 | 航空器電纜的壓接接頭 | Crimped joints for aircraft electrical cables |
| ISO 2016-1981 | 銅管用毛細管焊接接頭 組裝尺寸和試驗方法 | Capillary solder fittings for copper tubes; Assembly dimensions and tests |
| ISO 2048-1990 | 彈性密封圈型接頭的硬聚氯乙烯(PVC-U)壓力管的雙承口 最小配合深度 | Double-socket fittings for unplasticized poly(vinyl chloride) (PVC-U) pressure pipes with elastic sealing ring type joints; minimum depths of engagement |
| ISO 21004-2006 | 塑料管道系統.供水用基于熱塑性塑料的多層管道及其接頭 | Plastics piping systems - Multilayer pipes and their joints, based on thermoplastics, for water supply |
| ISO 21809-3-2008 | 石油和天然氣工業.管道運輸系統用掩埋于地下或淹沒于水下的管道外部覆層.第2部分:安裝接頭涂層 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings |
| ISO 22826-2005 | 金屬材料焊縫的破壞性試驗.激光和電子束焊接窄接頭的硬度試驗(維氏和努氏硬度試驗) | Destructive tests on welds in metallic materials - Hardness testing of narrow joints welded by laser and electron beam (Vickers and Knoop hardness tests) |
| ISO 23711-2003 | 彈性密封件.灌溉和排水設施用管接頭密封件材料的要求.彈性塑料 | Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers |
| ISO 2531-1998 | 輸水和輸氣用球墨鑄鐵管、配件、附件及其接頭 | Ductile iron pipes, fittings, accessories and their joints for water or gas applications |
| ISO 2553-1992 | 焊接、硬釬焊和軟釬焊接頭 圖樣上的符號表示法 | Welded, brazed and soldered joints; symbolic representation on drawings |
| ISO 2974-2005 | 柴油機.60度錐孔的高壓油管接頭管端部連接 | Diesel engines - High-pressure fuel injection pipe end-connections with 60 degrees female cone |
| ISO 3174-1994 | 航空器 用地面設備檢查液壓系統的連接接頭 螺紋式 | Aircraft - Connections for checking hydraulic systems by ground appliances - Threaded type |
| ISO 3253-1998 | 氣焊設備 焊接、切割和有關工藝設備的軟管接頭 | Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes |
| ISO 3458-1976 | 聚乙烯(PE)壓力管材和管件間的裝配接頭 內壓密封試驗 | Assembled joints between fittings and polyethylene (PE) pressure pipes ; Test of leakproofness under internal pressure |
| ISO 3459-1976 | 聚乙烯(PE)壓力管 用機械式管件裝配的接頭 內壓試驗法和要求 | Polyethylene (PE) pressure pipes; Joints assembled with mechanical fittings; Internal under-pressure test method and requirement |
| ISO 3460-1975 | 硬聚氯乙烯(PVC)壓力管材 公制系列 凹法蘭管接頭尺寸 | Unplasticized polyvinyl chloride (PVC) pressures pipes; Metric series; Dimensions of adapter for backing flange |
| ISO 3501-1976 | 聚乙烯(PE)壓力管材和管件間的裝配接頭 抗拉拔試驗 | Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of resistance to pull out |
| ISO 3503-1976 | 聚乙烯(PE)壓力管材和管件間的裝配接頭 彎曲時承受內壓的密封試驗 | Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of leakproofness under internal pressure when subjected to bending |
| ISO 3553-1-1987 | 道路車輛 點火線圈和分電器的高壓接頭 第1部分:插座型 | Road vehicles; High-tension connections for ignition coils and distributors; Part 1 : Socket-type |
| ISO 3553-2-1997 | 道路車輛 點火線圈和分電器的高壓接頭 第2部分:插頭型 | Road vehicles - High-tension connectors for ignition coils and distributors - Part 2: Plug-types |
| ISO 3926-1980 | 造船 內河航行 滑油和燃料輸入管接頭、配合尺寸 | Shipbuilding; Inland navigation; Couplings for oil and fuel reception; Mating dimensions |
| ISO 4038-1996 | 道路車輛 液壓制動系統 單喇叭口管、螺孔和陽螺紋接頭和軟管管端接頭 | Road vehicles - Hydraulic braking systems - Simple flare pipes, tapped holes, male fittings and hose end fittings |
| ISO 4039-1-1998 | 道路車輛 氣壓制動系統 第1部分:有平面密封面的管、陽螺紋管接頭和螺紋孔 | Road vehicles - Pneumatic braking systems - Part 1: Pipes, male fittings and tapped holes with facial sealing surface |
| ISO 4039-2-1998 | 道路車輛 氣壓制動系統 第2部分:有錐形密封面的管、陽螺紋管接頭和螺紋孔 | Road vehicles - Pneumatic braking systems - Part 2: Pipes, male fittings and tapped holes with conical sealing surface |
| ISO 4132-1979 | 承壓管用硬聚氯乙烯(PVC)和金屬的接頭管件安裝長度和螺紋尺寸 公制系列 | Unplasticized polyvinyl chloride (PVC) and metal adaptor fittings for pipes under pressure; Laying lengths and size of threads; Metric series |
| ISO 4347-2004 | 板式鏈、端接頭及槽輪.尺寸、計量力和抗拉強度 | Leaf chains, clevises and sheaves - Dimensions, measuring forces and tensile strengths |
| ISO 4397-1993 | 流體傳動系統和元件 管接頭及其附件 硬管外徑和軟管內徑 | Fluid power systems and components; connectors and associated components; nominal outside diameters of tubes and nominal inside diameters of hoses |
| ISO 4399-1995 | 流體傳動系統和元件 管接頭及其附件 公稱壓力系列 | Fluid power systems and components - Connectors and associated components - Nominal pressures |
| ISO 4434-1977 | 承壓管用硬聚氯乙烯(PVC)接頭管件 安裝長度和螺紋尺寸 公制系列 | Unplasticized polyvinyl chloride (PVC) adaptor fittings for pipes under pressure; Laying length and size of threads; Metric series |
| ISO 45-1990 | 航空器 壓力加油接頭 | Aircraft; pressure refuelling connections |
| ISO 451-1976 | 飛機.壓力加注潤滑油接頭 | Aircraft; Pressure re-oiling connection |
| ISO 485-1973 | 航空器的水-甲醇?jí)毫幼⒔宇^ | Aircraft water-methanol pressure connections |
| ISO 49 Technical Corrigendum 1-1997 | 符合ISO 7-1可鍛鑄鐵管螺紋接頭 技術勘誤1 | Malleable cast iron fittings threaded to ISO 7-1; Technical Corrigendum 1 |
| ISO 49-1994 | 符合ISO 7-1可鍛鑄鐵管螺紋接頭 | Malleable cast iron fittings threaded to ISO 7-1 |
| ISO 5031-1977 | 松散物料連續搬運設備 氣力輸送用接頭和軟管 安全規則 | Continuous mechanical handling equipment for loose bulk materials; Couplings and hose components used in pneumatic handling; Safety code |
| ISO 5178-2001 | 金屬材料焊接的破壞性試驗 熔焊接頭的焊接金屬的縱向拉申試驗 | Destructive tests on welds in metallic materials - Longitudinal tensile test on weld metal in fusion welded joints |
| ISO 5183-1-1998 | 電阻焊設備 外錐度1:10電極接頭 第10部分:錐度1:10圓錐形接頭 | Resistance welding equipment - Electrode adaptors, male taper 1:10 - Part 1: Conical fixing, taper 1:10 |
| ISO 5183-2-2000 | 電阻點焊 外錐度1:10電極接頭 第2部分:端推力電極用平行柄接頭 | Resistance spot welding - Electrode adaptors, male taper 1:10 - Part 2: Parallel shank fixing for end-thrust electrodes |
| ISO 5187-1985 | 焊接和相關工藝 用軟釬焊和硬釬焊接頭 力學試驗方法 | Welding and allied processes; Assemblies made with soft solders and brazing filler metals; Mechanical test methods |
| ISO 5290-2001 | 帶傳動 帶接頭的窄V帶槽輪 槽形截面為9N/J、15N/J和25N/J(有效系列) | Belt drives - Grooved pulleys for narrow V-belts - Groove sections 9N/J, 15N/J and 25N/J (effective system) |
| ISO 5291-1993 | 帶傳動 帶接頭的三角V帶槽輪 槽形截面為AJ、BJ、CJ和DJ(有效系列) | Belt drives; grooved pulleys for joined classical V-belts; groove sections AJ, BJ, CJ and DJ (effective system) |
| ISO 5356-1-2004 | 麻醉和呼吸設備.錐形接頭.第1部分:錐體和錐套 | Anaesthetic and respiratory equipment - Conical connectors - Part 1: Cones and sockets |
| ISO 5356-2-2006 | 麻醉和呼吸設備.圓錐形接頭.第2部分:螺紋承重接頭 | Anaesthetic and respiratory equipment - Conical connectors - Part 2: Screw-threaded weight-bearing connectors |
| ISO 5366-1-2000 | 麻醉和呼吸設備 氣管造口插管 第1部分:成人用插管和接頭 | Anaesthetic and respiratory equipment - Tracheostomy tubes - Part 1: Tubes and connectors for use in adults |
| ISO 5599-1-2001 | 氣壓傳動 五氣口方向控制閥 第1部分:不帶電接頭的安裝面 | Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector |
| ISO 5599-2 AMD 1-2004 | 氣壓傳動.五氣口方向控制閥.第2部分:帶可選電接頭的安裝面.修改件1 | Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector; Amendment 1 |
| ISO 5599-2-2001 | 氣壓傳動 五氣口方向控制閥 第2部分:帶可選電接頭的安裝面 | Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector |
| ISO 5620-1-1992 | 造船及海上結構物 飲水艙的注水接頭 第1部分:一般要求 | Shipbuilding and marine structures; filling connection for drinking water tanks; part 1: general requirements |
| ISO 5620-2-1992 | 造船及海上結構物 飲水艙的注水接頭 第2部分:零件 | Shipbuilding and marine structures; filling connection for drinking water tanks; part 2: components |
| ISO 5675-2008 | 農業拖拉機和機械.一般用快速液壓接頭 | Agricultural tractors and machinery - General purpose quick-action hydraulic couplers |
| ISO 5676-1983 | 農林用拖拉機和機械 液壓接頭 制動回路 | Tractors and machinery for agriculture and forestry; Hydraulic coupling; Braking circuit |
| ISO 5817-2003 | 焊接.鋼、鎳、鈦及其合金熔焊接頭(束焊除外).缺陷的質量分級 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections |
| ISO 5821-2009 | 電阻焊接.點焊電極帽接頭 | Resistance welding - Spot welding electrode caps |
| ISO 5828-2001 | 電阻焊設備 連接水冷接頭的二次連接電纜 尺寸及特性 | Resistance welding equipment - Secondary connecting cables with terminals connected to water-cooled lugs - Dimensions and characteristics |
| ISO 5829-1984 | 電阻點焊 內錐度為1:10的電極接頭 | Resistance spot welding; Electrode adaptors, female taper 1 : 10 |
| ISO 5855-3-1999 | 航空航天 MJ螺紋 第3部分:液體系統管接頭螺紋系統的極限尺寸 | Aerospace - MJ threads - Part 3: Limit dimensions for fittings for fluid systems |
| ISO 5866-1983 | 航空器 有扁接頭的2型和3A型插座式的換向繼電器 間隙和固定尺寸 | Aircraft; 2 and 3A plug-in base change-over relays, Type II, with crimped connections; Clearance and fixing dimensions |
| ISO 5887-1981 | 航空器 乘務員用調壓面罩與氧氣源的連接接頭 | Aircraft; Joints for connecting crew members' regulator masks to oxygen sources |
| ISO 594-1-1986 | 注射器、針頭及其他醫療器械為6%(魯爾)的錐形接頭 第1部分:一般要求 | Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment; Part 1 : General requirements |
| ISO 594-2-1998 | 注射器、針頭及其他醫療器械為6%(魯爾)的錐形接頭 第2部分:鎖緊接頭 | Conical fittings with 6% (Luer) taper for syringes, needles and certain other medical equipment - Part 2: Lock fittings |
| ISO 6038-1993 | 電影 70mm、65mm、35mm和16mm電影影片接頭 尺寸和位置 | Cinematography; splices for use on 70 mm, 65 mm, 35 mm and 16 mm motion-picture films; dimensions and locations |
| ISO 610-1990 | 刮板輸送機和刨煤機用高強度鋼鏈帶(無接頭無形連接) | High-tensile steel chains (round link) for chain conveyors and coal ploughs |
| ISO 6149-1-2006 | 用于液壓流體傳動和一般用途的管接頭.帶ISO 261螺紋和O形圈密封的油口和螺紋端頭.第1部分:帶锪孔溝槽中裝有 | Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal |
| ISO 6149-2-2006 | 用于液壓傳動和一般用途的管接頭.帶ISO 261螺紋和O形圈密封的油口和螺紋端頭.第2部分:重型(S系列)螺柱端頭 | Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends |
| ISO 6149-3-2006 | 用于液壓傳動和一般用途的管接頭.帶ISO 261螺紋和O形圈密封的油口和螺紋端頭.第3部分:輕型(L系列)螺柱端頭 | Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends |
| ISO 6149-4-2006 | 用于傳動和一般用途的管接頭.帶ISO 261螺紋和O形圈密封的油口和螺紋端頭.第4部分:內外六角氣門栓的尺寸、設 | Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs |
| ISO 6150-1988 | 氣壓傳動 最高工作壓力為10 bar、16 bar和25 bar(1 MPa、1.6 MPa和2.5 MPa)圓柱形快換接頭、插頭、連接尺寸 | Pneumatic fluid power; cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 MPa and 2,5 MPa); plug connecting dimensions, specifications, application guidelines and testing |
| ISO 6455-1983 | 承壓管用帶彈性密封圈型接頭的硬聚氯乙烯(PVC)管件 安裝長度的測定 公制系列 | Unplasticized polyvinyl chloride (PVC) fittings with elastic sealing ring type joints for pipes under pressure; Dimensions of laying lengths; Metric series |
| ISO 6696-1989 | 自行車 用于中接頭裝配的螺紋 | Cycles; screw threads used in bottom bracket assemblies |
| ISO 6699-1990 | 自行車 把橫管和把立管接頭 裝配尺寸 | Cycles; stem and handlebar bend; assembly dimensions |
| ISO 6772-1988 | 航空航天 流體系統 液壓軟管、導管和接頭組件的沖擊試驗 | Aerospace; fluid systems; impulse testing of hydraulic hose, tubing and fitting assemblies |
| ISO 6891-1983 | 木結構 機械緊固件接頭 強度和變形特性確定的一般原則 | Timber structures; Joints made with mechanical fasteners; General principles for the determination of strength and deformation characteristics |
| ISO 7169-2007 | 航空航天.液壓系統用24°錐形的、壓力范圍截至3000psi或21000kPa的可拆卸管接頭.采購規范(英制/米制) | Aerospace - Separable tube fittings for fluid systems, for 24° cones, for pressures up to 3000 psi or 21000 kPa - Procurement specification, inch/metric |
| ISO 7241-1-1987 | 液壓傳動 快換接頭 第1部分:尺寸和要求 | Hydraulic fluid power; Quick-action couplings; Part 1 : Dimensions and requirements |
| ISO 7241-2-2000 | 液壓傳動 快換接頭 第2部分:試驗方法 | Hydraulic fluid power - Quick-action couplings - Part 2: Test methods |
| ISO 7257-1983 | 航空器 液壓管接頭和連接接頭扭轉彎曲試驗 | Aircraft; Hydraulic tubing joints and fittings; Rotary flexure test |
| ISO 7289-1996 | 氣焊、切割及相關工藝用帶關閉閥的快速接頭 | Quick-action couplings with shut-off valves for gas welding, cutting and allied processes |
| ISO 7319-1992 | 航空航天.流體系統.24°錐孔米制管接頭的接口 | Aerospace; fluid systems; interface of 24° cone metric couplings |
| ISO 7320-1992 | 航空航天 流體系統螺紋密封連接接頭 尺寸 | Aerospace; couplings, threaded and sealed, for fluid systems; dimensions |
| ISO 7803-1987 | 商用道路車輛 轉向球接頭 | Commercial road vehicles; Steering ball joints |
| ISO 7876-4-2004 | 燃油噴射裝置.詞匯.第4部分:高壓管和末端接頭 | Fuel injection equipment - Vocabulary - Part 4: High-pressure pipes and end-connections |
| ISO 8056-4-1987 | 航空器 鎳鉻和鎳鋁熱電偶的延伸電纜 第4部分:壓接式對接接頭 尺寸 | Aircraft; Nickel-chromium and nickel-aluminium thermocouple extension cables; Part 4 : Crimp-type butt connectors; Dimensions |
| ISO 8092-1-1996 | 道路車輛 車載電氣線束的連接 第1部分:單極聯接接頭 尺寸和特殊要求 | Road vehicles - Connections for on-board electrical wiring harnesses - Part 1: Tabs for single-pole connections; dimensions and specific requirements |
| ISO 8092-3-1996 | 道路車輛 車載電氣線束的連接 第3部分:多極連接接頭 尺寸和特殊要求 | Road vehicles - Connections for on-board electrical wiring harnesses - Part 3: Tabs for multi-pole connections; dimensions and specific requirements |
| ISO 8267-1-2005 | 飛行器.牽引桿附屬接頭的接口要求.第1部分:干線飛行器 | Aircraft - Tow bar attachment fittings interface requirements - Part 1: Main line aircraft |
| ISO 8267-2-2005 | 飛行器.牽引桿附屬接頭的接口要求.第2部分:地方飛行器 | Aircraft - Tow bar attachment fittings interface requirements - Part 2: Regional aircraft |
| ISO 8434-1-2007 | 液壓傳動和通用金屬管連接件.第1部分:24°錐形接頭 | Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors |
| ISO 8434-2-2007 | 液壓傳動和通用金屬管連接件.第2部分:37°擴口管接頭 | Metallic tube connections for fluid power and general use - Part 2: 37° flared connectors |
| ISO 8434-3-2005 | 用于流體傳動和一般用途的金屬管接頭.第3部分:O形圈端面密封管接頭 | Metallic tube connections for fluid power and general use - Part 3: O-ring face seal connectors |
| ISO 8483-2003 | 玻璃增強熱固性塑料管及配件.栓結法蘭接頭設計驗證的試驗方法 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of bolted flange joints |
| ISO 8533-2003 | 玻璃增強熱固性塑料管及配件.膠合接頭或包好的接頭設計驗證的試驗方法 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of cemented or wrapped joints |
| ISO 8775-1988 | 航空航天 流體系統用氣氧充填接頭(新型) 尺寸(英制) | Aerospace; gaseous oxygen replenishment connection for use in fluid systems (new type); dimensions (inch series) |
| ISO 8793-1986 | 鋼絲繩 套圈卡緊環眼接頭 | Steel wire ropes; Ferrule-secured eye terminations |
| ISO 8795-2001 | 輸送人類生活用水用塑料管道系統 流動評定 塑料管道和管件及其接頭的流動值的測定 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints |
| ISO 8820-3-2002 | 道路車輛.熔斷體.第3部分:帶接頭的熔斷體(刀閘) | Road vehicles - Fuse-links - Part 3: Fuse-links with tabs (blade type) |
| ISO 8969-1990 | 木結構 單側沖孔金屬板緊固件和接頭的試驗 | Timber structures; testing of unilateral punched metal plate fasteners and joints |
| ISO 8970-1989 | 木結構 機械緊固件接頭的試驗 對木材密度要求 | Timber structures; testing of joints made with mechanical fasteners; requirements for wood density |
| ISO 9015-1-2001 | 金屬材料焊接的破壞性試驗 硬度試驗 第1部分：弧焊接頭的硬度試驗 | Destructive tests on welds in metallic materials - Hardness testing - Part 1: Hardness test on arc welded joints |
| ISO 9538-1996 | 航空航天 液壓管路安裝接頭及管接頭 平面彎曲試驗 | Aerospace - Hydraulic tubing joints and fittings - Planar flexure test |
| ISO 9623-1997 | 壓力流體用聚乙烯(PE)/金屬和聚丙烯(PP)/金屬接頭管件 螺紋的設計長度和尺寸 公制系列 | PE/metal and PP/metal adaptor fittings for pipes for fluids under pressure - Design lengths and size of threads - Metric series |
| ISO 9624-1997 | 壓力流體用熱塑性塑料管材 法蘭接頭和活套法蘭的適配尺寸 | Thermoplastics pipes for fluids under pressure - Mating dimensions of flange adapters and loose backing flanges |
| ISO 9691-1992 | 橡膠 管接頭的密封件制造工藝的建議 缺陷類型和描述 | Rubber; recommendations for the workmanship of pipe joint rings; description and classification of imperfections |
| ISO 9692-2-1998 | 焊接和相關工藝 接頭的制備 第2部分:鋼的埋弧焊 | Welding and allied processes - Joint preparation - Part 2: Submerged arc welding of steels |
| ISO 9692-3-2000 | 焊接和相關工藝 接頭制備的建議 第3部分:鋁及鋁合金的金屬焊條惰性氣體保護焊和鎢焊條惰性氣體保護焊 | Welding and allied processes - Recommendations for joint preparation - Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| ISO 9692-4-2003 | 焊接和相關工藝.接頭制備的建議.第4部分:包鋼 | Welding and allied processes - Recommendations for joint preparation - Part 4: Clad steels |
| ISO 9788-1990 | 航空貨運設備 固定航空貨物用承載能力為22250N(5000lbf)雙螺柱接頭的鑄件 | Air cargo equipment; cast components of double stud fitting assembly with a load capacity of 22250 N (5000 lbf), for aircraft cargo restraint |
| ISO 9939-1994 | 航空航天 滑油的壓力加油接頭(新型) | Aerospace; pressure re-oiling connection (new type) |
| ISO/TR 5987-1984 | 內河航行 噴水滅火系統 滅火水龍帶連接頭 一般技術要求 | Inland navigation; Water fire-fighting system; Couplings of fire hoses; General technical requirements |
| 編號 | 中文名稱 | 英文名稱 |